LG's owner manual supplied for LAN120HSV5 separates weak cooling, heating preparation and a fan continuing after shutdown. Where fitted, Energy Control can reduce cooling capacity, while Energy Saving can change the cooling target. Auto Clean can keep the indoor fan running after the off command.
An LG mini split not heating or cooling needs a different check depending on whether it delivers weak air, waits with the outlet nearly closed, or keeps its fan running after you switch it off. LG’s owner manual separates those three behaviors.
This page uses the wall unit manual LG supplies for LAN120HSV5. It also covers the optional cooling power controls in that document, which are worth checking when the unit runs but comfort falls short.
Before you start
What to carry: the original remote, a torch and your phone. Have the complete indoor model and any displayed message available for the service report.
Match the reference. The document here is LG MFL69491102, revision 19 dated January 2026, linked from the LAN120HSV5.AT3GEUS support page. LG marks several functions optional. Apply a special function check only when your own equipment and remote offer it.
Gas or electric? You are working with owner controls for an electric wall unit and its outdoor system. Keep all equipment service covers in place.
Renting? Pass the symptoms and settings to your maintenance contact. Mention whether the system has always behaved this way or changed after recent work.
LG says to cut off the supply if the unit gives off a smell or smoke. Its troubleshooting table also requires stopping and service for burning smells with strange sounds, abnormal indoor water leakage, an excessively hot or damaged power cable, improperly operating protective devices, or a self diagnosis error. Contact the service center for those conditions.
Before normal cleaning or maintenance, LG requires the supply disconnected and the fan allowed to stop. Do not reach into a running head because the remote says Off. Leave electrical testing, internal repairs and refrigerant work to service.
If the room stays warm during cooling
Compare the cooling request with LG's owner checklist
LG’s table asks whether the desired temperature is below the current room temperature and whether Fan Mode was selected. It says Fan Mode blows air without cooling or heating it. Use the actual cooling mode for a cooling request.
For poor cooling, LG also points to curtains, blinds or furniture blocking the head, dirty filters, escaping cool air and nearby heat sources. Address the visible obstruction or normal filter care before judging the result. The general cooling guide covers the broader airflow checks.
If those checks look right, review the optional settings below. They change what the controller asks for even when the mode says cooling.
If an energy setting is limiting the result
Distinguish Energy Control from Energy Saving
LG’s Energy Control instructions use the ENERGY CTRL. button to select steps. The first reduces power input by 20 percent against rated input, the second by 40 percent, and the optional third by 60 percent. The manual makes this a cooling function and says capacity may decrease when it is selected.
Those figures describe the input setting. They do not tell you how much heating or cooling your particular room is receiving. If the function is fitted and selected, compare its setting with the owner’s normal cooling instructions before treating reduced output as a mechanical fault.
Energy Saving is another optional function in this manual. LG says it increases the cooling target to 22 degrees C if the desired temperature was lower; a target above that stays unchanged. If the remote appears to undo a colder request, check whether this function is selected.
Keep the two names separate when reporting the problem. Send the actual function and step shown on your remote, rather than just saying an economy light is on.
If heating starts with almost no air
Observe whether preparation gives way to warm airflow
LG’s warm air troubleshooting entry describes a nearly closed vane and no indoor airflow while the outdoor unit operates at the start of heating. It says to wait until enough warm air has been generated for the indoor unit to blow.
The same table gives defrost its own entry. For this manual, LG says frost removal should finish in approximately fifteen minutes. Do not force the outlet open while the system is preparing warm air or defrosting.
LG also lists very low outdoor temperature as a reason the heating effect may be insufficient. If warm airflow never develops or the problem continues after the owner’s checks, use the service path at the end rather than repeatedly switching between heating and cooling.
If the fan continues after Off
Look for Auto Clean before treating the fan as stuck
LG says cooling and dehumidification leave moisture inside the indoor unit. Auto Clean removes it, and the manual describes the fan continuing for thirty minutes after shutdown when that function operates.
Its troubleshooting table tells the owner to allow that function to continue. That explains fan movement after an off command; it does not establish that the unit is still supplying heating or cooling to the room.
For a unit that actually shuts down during a run, LG’s separate table entry asks whether a timer has expired. Check the schedule if the stop follows a preset time. Keep that event separate from the fan finishing Auto Clean after you deliberately stopped operation.
When to send the findings for service
LG’s before service section says to contact the local service center if the problem persists after its checks. Send the full model, selected mode, room and target temperatures, energy function, and whether airflow eventually starts or stops.
For an error display, use the LG error code guide with the model beside it. A recurring fault is a different report from a deliberate owner setting. Leave the installer menu alone: LG warns that incorrect changes there can cause product problems or injury.
What each one takes
| What you find | What the next step involves |
|---|---|
| Fan Mode or an unsuitable cooling target | A normal owner mode or temperature adjustment |
| Energy Control or Energy Saving selected | Reviewing the equipped remote’s cooling power or target setting |
| Heating preparation or a defrost interval | Observation of the return to warm airflow |
| Auto Clean fan operation after shutdown | Allowing the moisture removal function to finish |
| Persistent poor output or a protective fault | Service diagnosis with the settings and symptoms supplied |
Questions people ask
Why will the fan speed button not change anything?
LG’s table lists Jet Mode or Auto Operation Mode as possible reasons. Some modes do not allow manual fan speed adjustment.
Why can I not change the temperature?
LG identifies Fan Mode and Jet Mode in that troubleshooting entry. Select an operating mode that allows temperature adjustment before treating the remote as faulty.
Can Comfort Air send the stream away from my chair?
Where fitted, LG says Comfort Air sets the vane to a preset position that deflects supply air away from the occupants. It is an airflow choice, rather than a cooling request.
Does the same heating indication always mean defrost?
No. LG’s heating instructions say an indication used during defrost also appears during preheating or when the set room temperature has been reached. Read it alongside the operating behavior.
Where is the manual used here?
LG provides the English MFL69491102 owner manual on its LAN120HSV5 product support page. Pages 31 to 33 contain the before service tables.
The other mini split guides: general heating delays, a head that will not start and indoor and outdoor noises.
Sources: LG wall mounted air conditioner owner's manual MFL69491102 Rev.19_011926, supplied on LG Canada's LAN120HSV5.AT3GEUS support page, pages 4, 5, 15, 19 to 23 and 31 to 33; original LG PDF and model support page saved in data/sources/lg-mini-split-not-heating
By



