Free, independent repair guides
HeatCoolFix

Braeburn Thermostat Not Working: Display, AC and Reset

Braeburn Thermostat Not Working: Display, AC and Reset
Short answer

Braeburn's 1020/1220 and 2020/2220 need 24VAC or two AA alkaline batteries. Check the power source, system mode and compressor delay before resetting. On a programmed 2020/2220, 85°F is the factory DAY cooling setting; a temporary change ends at the next scheduled event. Reset erases user settings and, on 2020/2220, programming.

A Braeburn thermostat not working can leave the screen empty, the cooling off or the temperature returning to a setting you did not expect. Braeburn’s 1020/1220 and 2020/2220 manuals give different checks for power, compressor waiting and programmed changes.

This page covers those four model numbers. The 1020 and 1220 are nonprogrammable; the 2020 and 2220 can run schedules. Use the model from your paperwork so a schedule explanation is not applied to the wrong control.

Before you start

What to carry: a torch and, if your installation uses them, two new AA alkaline batteries. Read the current room temperature separately from the smaller desired temperature on the screen.

Renting? Tell the person responsible for repairs whether the display is blank, cooling never starts or the desired temperature changes by itself.

Keep testing within the manufacturer's limits.
Braeburn’s guides reserve installation for experienced service technicians and require power to the heating or cooling equipment to be disconnected before installation. Keep the mounted base, wiring and installer switches in place during these owner checks.

For these models, Braeburn says not to select COOL when the outdoor temperature is below 50°F, because the cooling equipment could be damaged. Do not run a cooling test in cold weather.

If the screen is blank

BRAEBURN: IDENTIFY THE POWER SOURCEAAAA24VACCATwo AA alkaline batteriesCorrect polarity; refit the body.B24VAC installationWiring checks stay with the installer.CLow battery indicatorReplace the fitted cells when shown.AB
Braeburn specifies 24VAC or two AA alkaline batteries for the four models covered here. Batteries can also provide backup on a wired installation. This is a schematic, not a terminal diagram.
Check 1Two AA alkaline cells if batteries are fitted; a service check for missing wired power

Check the installed power source

Braeburn says both model pairs require 24 Volt AC power or two correctly installed AA alkaline batteries. When connected to 24VAC, the batteries may be installed as backup. A blank screen is a reason to check that supply arrangement before trying buttons at random.

For battery replacement, Braeburn’s maintenance instructions say to pull the thermostat body gently from the base, replace the old batteries and match the marked plus and minus ends. Gently push the body back onto the base afterward. Do not unscrew the mounted plate or handle its terminals.

Braeburn says to change the cells when the low battery indicator appears. If correct new batteries and careful refitting do not restore the display, give that result to the installer. For a broader comparison of battery types, see thermostat batteries.

The display works, but AC does not start

Check 2An owner setting check; no parts to buy

Check SYSTEM, FAN and the desired temperature

Braeburn’s operating sections say the SYSTEM switch selects COOL, OFF or HEAT. Select COOL for a cooling request and use the temperature keys to put the desired temperature below the current room reading, subject to the outdoor limit above.

The same guides distinguish FAN ON, which keeps the fan running, from FAN AUTO, which runs it with heating or cooling. Air moving from the vents after selecting FAN ON is not the same as a cooling request.

Braeburn labels its cooling status indicator COOL ON. Tell the installer whether that indication appears and whether the equipment responds. Do not bridge the thermostat wires to force the AC to run.

Check 3Waiting through the built-in delay; diagnosis if operation does not follow

Allow for the model's compressor protection

Braeburn says these models include an automatic compressor protection delay after the system compressor turns off.

Let that protection run before deciding the thermostat has ignored the request. Repeatedly switching modes makes it harder to observe what happens after a single request. Leave installer test procedures and changes to the protection settings to the service person.

If the wall control is responsive but the system still does not operate, the thermostat not working guide explains the next equipment checks.

If a 2020 or 2220 keeps returning to 85

2020 / 2220: THE FACTORY DAY EVENTDAY8:00 amCooling target85 FAFactory DAY cooling85 F at 8:00 am.BTemporary adjustmentProgram resumes at the next event.CExtended adjustmentHOLD uses its selected duration.
Braeburn's 2020/2220 factory schedule sets DAY cooling to 85°F at 8 a.m. This example applies when that program is active; it is not a setting for every Braeburn model.
Check 4A schedule or Hold adjustment if the program is the cause

Look for the active program event

For a programmed 2020 or 2220, Braeburn’s factory schedule sets the DAY event to 85°F for cooling at 8 a.m. Its factory schedule tables show that setting for both seven day and weekday/weekend programming.

Braeburn says a flashing program event indicator means the program has been temporarily bypassed and will resume at the next scheduled event. If you lower the temperature temporarily and it returns at the DAY time, compare the programmed event with what you wanted.

Braeburn’s procedure for an extended change is to press HOLD until HOLD appears, then adjust the desired temperature. Braeburn’s Extended Hold Period setting makes that Hold permanent or limits it to 24 hours. For an ongoing schedule change, use the model’s PROG procedure to change the event rather than lowering the temperature again every morning.

The 2020/2220 guide also tells the user to check the current time and day, including AM and PM, before programming. A wrong clock can put the right temperature event at the wrong point in your day.

Use reset after understanding what it erases

Check 5Restoring user settings and, on programmable models, the schedule

Keep a record before pressing the recessed button

Braeburn’s 1020/1220 reset section says the button erases user settings. Its 2020/2220 section says it erases user settings and programming. Record the settings you want to restore before using it.

For these named models, Braeburn identifies a small hole on the front marked reset. Its instructions are to press the recessed button gently with a small object such as a toothpick or paper clip. This is a model specific reset, not a reason to open the equipment cabinet.

Afterward, restore the desired mode and temperature. On a programmed 2020/2220, also check the clock and schedule before leaving it unattended. The thermostat reset guide covers other control families.

What each one takes

What you find Work involved
Low batteries on a fitted battery supply Correct cells, polarity and refitting
No display after the power checks Installer diagnosis of the power supply and control
Fan runs without a cooling request Checking SYSTEM and FAN separately
2020/2220 returns to its DAY setting Clock, program event or Hold adjustment
Reset used on a programmed control Restoring the user’s settings and schedule

Questions people ask

Does every Braeburn thermostat need batteries?

No. The four models here allow 24VAC or the specified batteries, with optional battery backup on wired power. Use the power arrangement for your installation.

Is 85 an error code on the 2020 or 2220?

Braeburn’s schedule table uses 85°F as a DAY cooling target. Check whether that is the desired temperature shown on your screen; this program explanation does not identify every appearance of the number.

Why does my 2020/2220 show NO when I press PROG?

Braeburn says an installer configured nonprogrammable mode has no program to access. In that configuration, pressing PROG or HOLD shows NO. Ask the installer about the selected mode if you expected a schedule.

What does SERVICE mean on the 2020/2220?

Braeburn identifies it as a selected user service reminder, tied to its Service Filter Monitor. Give the full display to the repairer rather than treating that word alone as a compressor fault.

Why does my 1220 show NO EMER SET?

Braeburn says that message appears if EMER is selected while the 1220 is configured for a conventional system. Emergency heat is its heat pump backup option. Have the installer check configuration if it does not match your equipment.

The other thermostat guides: thermostat says Hold, thermostat wiring, and thermostat not working.

Sources: Braeburn 1020/1220 Detailed Installer Guide 1020W-100-03, sections 1, 4, 6, 7 and 8; Braeburn 2020/2220 Detailed Installer Guide 2020W-100-06, sections 1, 4, 5, 6, 7, 8 and 9. Operating and maintenance sections used for owner steps; installation and wiring remain installer work.