Free, independent repair guides
HeatCoolFix

Furnace Gas Valve: What Fails, and What It Costs

Furnace Gas Valve: What Fails, and What It Costs
Short answer

The gas valve is blamed far more often than it fails, because it is the last thing in the starting sequence and everything ahead of it that says no looks exactly the same from where you are standing. Here is how to tell a valve fault from the five cheaper things that copy it.

A furnace gas valve is an expensive part, so it is worth ruling out everything else before one is replaced.

That is not because anybody is dishonest. It is because the valve is the very last step in the starting sequence, so every one of the four things ahead of it that refuses to play produces the same picture: no gas, no flame, no heat.

Before you start

What to carry: a torch. Fifteen minutes, and it is mostly standing still and listening.

Gas or electric? Only a gas furnace has one. An electric furnace heats with elements and has no valve, no flame and no flue, so none of this applies.

Watch a whole start. Turn the thermostat up five degrees and stand at the furnace from the moment it wakes up. What happens in the next minute is the whole diagnosis, and you can do all of it with the door on.

Three lines not to cross with a gas valve. If you can smell gas, leave. Out of the house, no light switches, no phone until you are outside, then call the gas company from there. That comes before everything on this page.

Never put a jumper across a gas valve to test it. It is a trick that gets passed around and it does exactly what it sounds like: it opens the gas with nothing watching whether it lit.

Never turn the regulator screw on it. Setting gas pressure needs a manometer and a reading, and guessing at it makes a furnace that soots, overheats or burns wrong.

Why the valve is last, and what that means for you

THE VALVE IS ASKED LAST 1 Thermostat it calls 2 Inducer clears the flue 3 Pressure switch listens to it 4 Igniter glows orange 5 The gas valve opens, at last 6 Flame sensor proves the flame Four things have to say yes before the valve is even asked. If the igniter never glows, the valve is not your problem.
Four things have to say yes before the valve is even asked. That is why so many faults look like a gas valve from where you are standing.
Check 1

Watch the sequence and find where it stops

Every modern furnace starts the same way, in the same order, every time.

1. The thermostat calls. Nothing happens at the furnace at all if this does not: how to prove a thermostat is really calling for heat.

2. The inducer spins up and runs on its own for 15 to 30 seconds, clearing the flue.

3. The pressure switch closes, because it is listening to that inducer. This one stops more furnaces than the valve ever will: the five places to look when it will not close.

4. The igniter glows, orange and bright, for about 20 seconds.

5. Only now is the valve asked to open. A click, a soft whoosh, and the burners light.

6. The flame sensor proves the flame within a few seconds, or the valve shuts again.

So the question is not “is it the valve”. The question is how far down that list it gets. If the igniter never glows, the valve is irrelevant. If the igniter glows and then everything shuts down, you are finally in gas valve territory, and even then step 6 is the more likely one.

Listening for the click

A CLICK, THEN FLAME click, whoosh, then burners The valve did open so look at the flame sensor IT GLOWS, THEN NOTHING no click, and no whoosh Now it is a suspect with its wiring and the board
The valve makes a noise when it opens. Whether you hear it, and what happens in the three seconds after, splits the whole thing in two.
Check 2

Name what you hear after the igniter glows

A click, a whoosh, flame, then it all shuts down a few seconds later. The valve worked. It opened, it lit, and something told the board there was no flame. The flame sensor is the first suspect, and it is a cheap clean rather than a part: the twenty minute fix behind many of these.

The igniter glows, then nothing at all, then the inducer stops. No click and no whoosh. Now the valve is a genuine suspect, alongside the wiring to it and the board that drives it.

A click but no flame. The valve is being told to open and is not passing gas, or there is no gas to pass. Check the supply before the part.

It lights fine from cold, then refuses after twenty minutes, every time. That is the typical sign of a failing valve coil. It works until it warms up, then goes open circuit, then works again once it cools, which is why it always seems fine when somebody comes out.

Nothing happens at all, no inducer either. Then you are much earlier in the sequence than the valve: the free checks in order.

The cheap things that look exactly like it

Check 3

Rule these out before anybody quotes you a valve

The gas cock beside the furnace. A small lever on the pipe near the valve. In line with the pipe is on, across it is off. It gets closed during a service and occasionally not reopened.

The knob on the valve itself. Older valves have ON, OFF and PILOT. Anything other than ON and the furnace cannot fire.

The meter, after any gas work. If the cooker is also dead, this is not a furnace fault at all.

A tripped rollout or limit switch. Both of these cut power to the valve on purpose. Replacing the valve with either of those tripped puts a new part in front of an old warning: what a tripping limit is telling you.

The low voltage wires to the valve. Two small spade connectors that vibrate loose over twenty years. Free to push back on with the power off.

The board. If the board never sends the signal, a perfect valve does nothing, and the two are told apart with a meter in about a minute by somebody who has one.

Questions people ask

Can I fit one myself?

It is the one furnace part where the honest answer is no for most people. It is a gas joint that has to be made and leak tested, and the valve has to be the right one for that furnace rather than one that looks the same.

Somebody said my valve is stuck. Is that a thing?

It happens, mostly on old valves and on ones that have had dirt or water through them. It is much rarer than the coil failing when hot, and far rarer than the five cheaper faults above.

Is there any way to test it at home?

By ear and by sequence, which is what this page is. Anything beyond that means measuring voltage at the valve while a live furnace tries to light, and that is the point to hand it over.

Mine works all summer for hot water but not for heat.

Then you have a boiler with one valve doing both, or a separate water heater with its own. Either way, something that works for one call and not the other points at the control side rather than the valve.

How long should a gas valve last?

Usually the life of the furnace. A failure at eight or ten years is worth asking about, especially if the furnace short cycles, because thousands of extra open and close operations a season is what wears one: why a furnace that keeps stopping wears itself out.

The quote includes a valve and a board together.

Ask which one was measured and which one was assumed. Both can fail, but they are told apart with a meter, and two guesses at once on an old furnace is the moment to price a replacement instead.

Sources: Carrier 58SC0A/58SC1A instructions and Lennox ML180UH installation instructions 507323-01 (heating sequence of operation), White-Rodgers 50M56U-843 instructions (timing specifications), and Carrier troubleshooting guide 58-3T (ignition proving failure checks)