Free, independent repair guides
HeatCoolFix

American Standard Furnace Not Heating: AUE1 Checks

American Standard Furnace Not Heating: AUE1 Checks
Short answer

American Standard's listed AUE1 and ADE1 furnaces delay the indoor blower for 45 seconds after flame confirmation. That pause differs from a failed ignition attempt or a blower that keeps running without useful heat. Use the model, startup behavior and recent service history to narrow the next check.

An American Standard furnace not heating needs a different explanation when flame is present but the room blower has not started yet. American Standard’s AUE1/ADE1 instructions specify a 45 second blower delay after flame confirmation.

This guide covers the A-prefix models in installer guide 18-CD19D4-26, including AUE1A060A9361A and ADE1B080A9451A. It concentrates on the heating sequence and air delivery. The separate American Standard furnace error code guide handles the flash counts.

Before you start

What to carry: a torch, your phone and the equipment paperwork. Gather the full model and the details you already noticed when the heat stopped. Do not restart a failed furnace just to fill gaps in the account.

Gas or electric? The manufacturer’s AUE1/ADE1 document covers gas furnaces with a fan assisted combustion system. An electric air handler is outside this page’s scope.

Renting? Give the maintenance contact the model and symptoms, especially if work was recently done on the furnace.

Use the shutdown instructions before investigating a failure. If you smell gas, American Standard’s guide says not to light an appliance, touch switches or use an indoor phone. Leave and call the gas supplier from outside, follow its instructions, and call the fire department if the supplier cannot be reached.

For overheating or gas that will not shut off, the guide specifically requires gas off before electrical power off. If you cannot reach a shutoff safely, leave and get emergency help.

For other electrical, fuel or mechanical failures, American Standard’s owner instructions require shutting off the gas supply and electrical power, then contacting the designated service agency. Use only accessible shutoffs; leave internal access to service.

American Standard requires power disconnected before blower door removal and warns that an open or loose door can release dangerous fumes. Keep panels secured. Installation and service belong to qualified personnel.

When nothing happened after a panel was opened

Check 1A supply and door switch check by service

Include recent cabinet access in the report

Was the furnace quiet from the start, or did the problem appear just after maintenance? Give the service agency that detail before discussing an igniter.

American Standard says the AUE1/ADE1 blower door switch cuts power to both the blower and gas valve when the door is removed. Its instructions require every panel securely closed for safe operation.

Do not hold that switch in. For the broader supply and thermostat checks, the furnace not working guide is the next reference. Keep this page for the named models’ heating behavior.

When the exhaust fan ran but the burners did not light

AUE1 / ADE1: THREE SEPARATE PERIODSAWARMUPAbout 17 secondsBIGNITION TRIAL6 secondsCBLOWER DELAY45 seconds after flameAIgniter warmupStarts after pressure proving;approximately 17 seconds.BFlame confirmationThe guide specifies a6 second ignition trial.CIndoor blower startsIts 45 second delay startsafter flame is confirmed.Describe the missing eventDraft only, ignition attempt,or flame without room airflow?
Timing landmarks from the listed AUE1/ADE1 sequence: approximately 17 seconds of igniter warmup, a six second ignition trial, then a 45 second blower delay after flame confirmation. These are separate periods.
Check 2Draft and ignition diagnosis, without owner meter tests

Identify which part of the attempt you noticed

In American Standard’s sequence, a thermostat heat request starts a control self check. The guide requires the pressure switch initially open and the limit switches closed before energizing the draft blower.

American Standard then starts igniter warmup when the pressure switch closes as that blower reaches speed. The guide gives approximately 17 seconds of warmup before the gas valve is energized, with flame confirmation during a six second ignition trial.

Tell service whether you heard only the small exhaust fan, saw an ignition attempt, or saw flame appear. Use an existing viewing opening if the information was visible there; cabinet access is unnecessary for this report.

The general ignition guide explains the components. Ask service to use this model’s instructions for measurements and replacement decisions.

When flame appeared before air reached the rooms

Check 3Compare the observation with the specified sequence

Keep the blower delay separate from failed ignition

American Standard starts the listed models’ 45 second fan on delay after the flame sensor confirms ignition. Its indoor blower runs after that delay and continues through the heating cycle.

If you saw established flame and then waited for the room blower, include the order of those events. If flame never appeared, the blower delay is not an explanation for the missing ignition.

Do not touch the igniter to check its temperature. American Standard’s service section describes the hot surface igniter as fragile and warns that touching it can cause severe burns.

When the blower kept going after the burners stopped

Check 4Review of blower timing and the installed control

Distinguish the end of a heat call from lost heat

American Standard says a satisfied thermostat ends the heat call, closes the gas valve and stops the induced draft blower. Its indoor blower continues for the fan off period.

The main sequence describes 100 seconds for that period. However, American Standard’s page 24 blower timing note specifies selectable heating delays of 60, 100, 140 or 180 seconds, with a 100 second factory setting.

Give service the actual stopping behavior and any recent control replacement. American Standard’s selectable delays mean a blower running beyond 100 seconds need not indicate a fault.

If the air stays cool throughout the demand for heat, use the cold air guide alongside the startup information here. A normal end of cycle delay does not explain an entire heat call without heat.

When the burners run but the heating feels wrong

AUE1 / ADE1: WHEN IT LIGHTS BUT HEAT FEELS WRONGABCAOutlet air temperatureAmerican Standard requiresthe nameplate range check.BInlet air temperatureService checks both sidesof the furnace air path.CBlower adjustmentUse the installed furnacewiring diagram and motor.Tell service what changedInclude recent motor workor a control replacement.
American Standard's airflow adjustment uses inlet and outlet temperatures against the furnace rating. The blower setting is a service adjustment, not a thermostat shortcut. The sketch shows an upflow AUE1 air path rather than a duct installation.
Check 5Measurements and blower setup by the service agency

Ask for the rated temperature and airflow checks

Describe whether the complaint began after blower work, a motor replacement or another repair. American Standard’s airflow adjustment section calls for checking inlet and outlet air temperatures against the furnace nameplate ranges.

The guide directs the technician to the wiring diagram when airflow needs changing. That makes the installed motor and wiring part of the check; there is no universal speed setting to copy from another American Standard furnace.

Leave motor connections and control switches alone. Ask service to record the measured temperatures and the applicable nameplate range with its diagnosis. That gives you something concrete to discuss if the furnace lights but the rooms still do not warm as expected.

What each one takes

Situation Work involved
No response after maintenance Check the supply and secured door arrangement
Draft fan without successful ignition Check pressure proving, ignition and gas delivery
Flame followed by a blower pause Compare the sequence with the specified fan on delay
Blower run after the heat call ends Verify the applicable fan off setting
Burners operate but air delivery seems wrong Measure temperatures and verify blower setup

Questions people ask

Where can I find the source instructions?

The source is installer guide 18-CD19D4-26. Its cover lists the furnace models and allows an A or T prefix. This page uses the listed American Standard A-prefix models.

Should the blower motor need regular oiling?

American Standard says these direct drive motors have permanently lubricated bearings and does not recommend lubrication under normal use. Do not add oil as a heating repair.

Does a yellow flame need attention?

American Standard’s burner service section says accumulated foreign material may cause yellowing flame or delayed ignition, and either condition requires a service call. Do not attempt burner removal yourself.

Can I relight these burners with a match?

No. American Standard describes a hot surface direct ignition device that lights these burners automatically, and its lighting warning prohibits trying to light them by hand.

Does the Trane S9V2 article cover the same startup?

Use each model’s document. The Trane S9V2 heating guide follows a different installer guide and includes second stage operation. Its timings and control setup should stay with that model.

The other furnace guides: furnace inducer motor, furnace limit switch, and furnace short cycling.

Sources: Trane / American Standard Installer's Guide 18-CD19D4-26 for listed AUE1 and ADE1 gas furnaces, pages 1, 17, 20, 21, 22 and 24