Free, independent repair guides
HeatCoolFix

Armstrong Air Furnace Error Codes: Flashes and E Codes

Armstrong Air Furnace Error Codes: Flashes and E Codes
Short answer

Three flashes on the A80UH1E controls covered here mean failed ignition or flame lost during a heat call, Allied Air says. The A97USMV uses a different numbered chart. Match the model and control first, then separate a normal heartbeat from a fault pattern.

Armstrong Air furnace error codes need a model number beside them. Allied Air’s A80UH1E service manual uses a flashing LED; its A97MV upflow service manual lists numbered faults such as E270 and E311.

If your furnace gives three flashes, start with the A80UH1E chart below only when the model and control match. A number copied from a different Armstrong furnace can send you toward the wrong repair.

Before you start

What to carry: a torch, your phone and the furnace model number. Record one complete light pattern or the full display message before changing anything. Include the E in an E code.

Gas or electric? Both manuals used here are for gas furnaces. These charts do not cover electric air handlers, heat pumps or an outdoor unit’s diagnostic light.

Which control? The A97MV chart here covers the A97USMV upflow and horizontal furnace only. Match the model label and the diagnostic chart supplied with the furnace. The A80UH1E manual distinguishes controls ending in 02 and 03. If confirming the board requires opening the cabinet, leave that identification to the technician.

Renting? Send the recording and model number to the landlord or maintenance team. Say whether the house has lost heat or the furnace still runs.

Stop at the safety codes. Eight flashes on the listed A80UH1E controls, or E200 on the listed A97MV control: Allied Air identifies an open rollout circuit. Its A80UH1E manual lists a blocked heat exchanger, blocked flue and inadequate combustion air as possible rollout causes. Leave the reset button alone and arrange urgent service.

E241 or E275 on this A97MV: Allied Air directs the technician to shut off gas and investigate valve leakage. E241 means flame is still present out of sequence; E275 means that flame signal has gone. Neither is a routine reset request.

Gas smell takes priority over any code. Allied Air’s A80UH1E instructions say to stop, immediately call the gas supplier from a neighbor’s phone and follow their instructions.

Do not light the burners by hand. Allied Air says the A80UH1E uses an automatic ignition device.

Before any maintenance: Allied Air requires electrical power off at the disconnects and warns that the furnace may have multiple supplies. Keep live board tests, gas adjustments and safety switch work with a qualified HVAC technician.

Read the A80UH1E light correctly

A80UH1E: READ THE PAUSEAn even heartbeatOne second on, one second off02 control: normal in all modes03 control: idle, fan or coolingThree flashes, then a pause3 sec pauseCounted group repeats03 control rapid flash withoutthat pause can mean heating.Illustrative patterns. Match the control revision before interpreting the light.
Allied Air's A80UH1E tables separate an even heartbeat from a counted fault group. The 03 control also has a continuous rapid flash for heating.
Check 1No parts needed to record the pattern

Count the group, not the heartbeat

Allied Air defines the A80UH1E heartbeat as one second on and one second off. A fault uses half second flashes, then a three second pause before repeating. Count the flashes between the longer pauses.

The control revision changes normal operation. In table 4, the 02 control uses its heartbeat during all operating modes without errors. In table 5, the 03 control uses a heartbeat for idle, fan and cooling, and continuous rapid flashing for a heat call or burner operation.

For help recognizing a repeating group, see how to count a furnace blinking light.

Allied Air’s A80UH1E fault chart, 02 and 03 controls, manual 508096-01:

Flashes What this control reports
Light off No control power, or a board fault
1 Supply polarity reversed
2 Incorrect earth ground
3 Burner did not light, or flame was lost during the heat call
4 Weak flame signal
5 Ignition attempts or flame recycles exceeded; Watchguard
6 Unused in these tables
7 Primary or secondary limit open, including extended limit opening
8 Rollout switch open
9 Pressure switch did not close, or opened during the heat call
10 Watchguard after five pressure switch openings in one heat call
11 Pressure switch already closed before the inducer starts
12 Flame detected with the gas valve unpowered
13 Low supply voltage

Three flashes and ignition lockouts

Check 2Diagnosis of ignition and flame sensing before buying parts

Separate lost flame from a weak signal

Three flashes has two possibilities. Allied Air’s A80UH1E table includes both a burner that failed to light and flame lost during a heating demand. Tell the technician which happened if you observed it through an existing viewing window; do not remove a panel to watch.

Four flashes is more specific. That table identifies low flame signal and points to the flame sensor. It does not turn every three flash fault into a sensor replacement. The flame sensor guide explains what that part detects.

Five flashes is Watchguard. Allied Air describes exceeded ignition retries or recycles. Its A80UH1E ignition sequence restarts after a 60 minute Watchguard period when the burner fails to establish flame through the allowed trials. A restart does not identify or repair the original cause.

A97MV numbered codes are a separate list

These selected heating faults come from Allied Air’s A97MV upflow service manual, table 13. They are not flash counts. Use the full manual for a code outside this selection.

Code Allied Air’s meaning for this control
E200 Rollout circuit open now or previously; hard lockout
E201 Control cannot communicate with the indoor blower
E223 / E224 Low pressure switch failed open / failed closed
E225 / E226 High pressure switch failed open / failed closed
E240 Low flame current during operation
E241 / E275 Flame out of sequence, still present / signal now gone
E250 Open limit circuit
E270 Too many ignition retries without sensed flame current
E271 / E272 Retry / recycle lockout ending with a pressure switch opening
E273 Too many recycles, last caused by flame failure
E274 Recycle lockout involving the limit circuit
E291 Heating airflow below the minimum
E311 Heating rate reduced to suit available blower airflow
A97USMV: KEEP THE FAULTS SEPARATEAE270 / E273Ignition or lost flameGas flow, ignition and flame sensing checksBE223 to E226Pressure provingMeasured pressure, vent and inducer checksCE291 / E311Heating airflowFilter, ducts and blower performanceService checks from Allied Air table 13. These are not LED flash counts.
Selected A97MV faults point to different service checks. Allied Air separates flame, pressure proving and airflow problems.
Check 3A service visit for pressure measurements or flame current tests

Keep pressure faults separate from flame faults

For A97MV E270, Allied Air checks gas flow, burner ignition and flame sensor current. For E273, it checks flame sensing and grounding after flame failure during operation.

For A97MV E223 through E226, Allied Air checks pressure switch operation, measured pressure, venting and the combustion air inducer. A code naming the switch is therefore a starting point for testing, rather than an instruction to buy that switch.

The pressure switch guide explains the air path involved. Leave tubing, wiring and switch bypasses alone.

Check 4A filter if needed, or duct and blower service

Give airflow warnings their own check

Allied Air’s A97MV E291 entry checks a dirty filter, airflow restrictions and blower performance. Its E311 entry checks the filter and ducts while the furnace reduces its heating rate to match airflow.

If your filter is accessible for owner maintenance, switch off all electrical supplies before replacing it. Allied Air also says to wear gloves and protective clothing when handling the furnace because sheet metal edges can cause injury. Leave internal blower work and duct changes to the service company. The limit switch guide explains the overheating side of this problem.

For A97MV E201, Allied Air also considers missing motor power and loose wiring. Allied Air says E201 can involve either the motor or the control.

Before the technician arrives

Allied Air’s A80UH1E manual says its last ten errors remain stored even when power is removed.

What each one takes

Finding Work to expect
A counted light pattern Match the model and board before choosing a test
Ignition or lost flame Ignition, gas supply and flame sensing diagnosis
Pressure proving trouble Pressure readings and inspection of the vent and inducer
Restricted airflow Filter inspection, then blower or duct work if needed
Rollout or flame out of sequence Urgent safety diagnosis before further operation

Questions people ask

Where is the Armstrong Air furnace error codes PDF?

Both maker manuals are available from Allied Air: A80UH1E service manual, tables 4 and 5, and A97MV upflow service manual, table 13.

Does three flashes mean a pressure switch problem?

Not on the A80UH1E controls shown here. Allied Air assigns three flashes to failure to light or lost flame. Its pressure switch faults are grouped under nine, ten and eleven flashes.

Is continuous rapid flashing a fault?

On the A80UH1E 03 control, Allied Air lists that as a heat call or burner operation. A counted group with a longer pause is different; check 1 explains the timing.

Can I use these flash codes on an A97MV?

Use the A97MV numbered table for the control covered here. Do not translate an E code into an A80UH1E flash count, even when the two descriptions sound similar.

Should I clear the stored errors before service?

Leave them available. Allied Air provides an error recall function on the A80UH1E control, so the technician can compare earlier faults with the current complaint.

The other furnace guides: blinking lights, pressure switches, flame sensors and rollout switches.

Sources: Allied Air A80UH1E / 80G1UHE Service Manual 508096-01, issue 2037, tables 4 and 5; Allied Air A97USMV Upflow/Horizontal Service Manual 508146-01, issue 2241, table 13 (A97MV product family).