Free, independent repair guides
HeatCoolFix

Goodman Furnace Not Heating: Find the Stopping Point

Goodman Furnace Not Heating: Find the Stopping Point
Short answer

For the Goodman GM9S80 and GMVC96 versions covered here, follow the startup sequence before choosing a part. The inducer, igniter, flame and house blower have separate jobs. Goodman's GMVC96 instructions also distinguish low heat from high heat and the blower's normal delay after the burners stop.

A Goodman furnace not heating is easier to describe when you know which part of startup is missing. The small exhaust fan starting, the burners lighting and the house blower moving air are separate events in Goodman’s sequence.

This page follows the GM9S80 in Goodman’s August 2021 installation manual and the GMVC96/GCVC96 in its November 2014 service instructions. The GMVC96 sequence below is the conventional two stage thermostat sequence in that document. Other controls, including communicating systems, need their matching instructions.

For a flashing light or a fault message, Goodman furnace error codes covers the *MSS9 and *M9S80 controls. The older GMVC96 display in the service manual here has its own legend. Keep that distinction alongside what the furnace did immediately before it stopped.

Before you start

What to carry: a torch and your phone. Collect the furnace model, the thermostat model and a description of one attempted heating cycle. Watch only through an existing observation window, with the doors fitted.

Gas or electric? These are gas furnaces. Goodman’s GM9S80 instructions describe automatic ignition; there is no burner for you to light by hand. An electric air handler or an outdoor heat pump needs a different troubleshooting path.

Renting? Send the model and symptoms to the person responsible for the heating system before authorizing repairs.

Leave gas and safety circuits alone. Goodman’s safety instructions say not to light an appliance, touch electrical switches or use a phone inside the building if you smell gas. Leave the building and call the gas supplier from a neighbor’s phone; follow its instructions. If you cannot reach the supplier, Goodman says to call the fire department.

If a GM9S80 overheats or its gas supply fails to shut off, Goodman says to close the external manual gas valve before switching off electrical power.

The GM9S80 manual prohibits defeating the blower door interlock. Goodman’s service instructions require electrical power disconnected before service and reserve the internal work for trained technicians. Do not hold that switch in to watch an exposed furnace run.

Know which part is supposed to start next

GM9S80: FOLLOW THE HEATING SEQUENCEAInducerBIgniterCFlameDIndoor blowerAPressure provingPrepurge starts with switch closedBIgniter energizedAfter the prepurge is completeCGas and ignitionThe control detects the flameDHouse airflow followsIndoor blower has a 30 second delay
The GM9S80 heating sequence in IOG-2030A. The control must detect the pressure switch closed before its prepurge period begins.

Goodman’s GM9S80 sequence starts with the thermostat calling for heat and the control checking the safety circuits. The control energizes the inducer, the small blower that handles combustion gases. Its prepurge begins once the pressure switch is detected closed.

The igniter comes next, then the gas valve and flame. Goodman specifies a 30 second delay before energizing the indoor blower on heating speed. That gives you a useful distinction: no flame and no warm air is different from a flame that remains on while the house blower never starts.

Check 1Outside observations first; electrical testing if needed

If nothing starts, preserve the control reading

Start with the general furnace power and thermostat checks if the equipment is silent. For the GM9S80, make sure the blower door has been refitted correctly after recent work; its interlock interrupts voltage when the door opens.

On the older GMVC96 control in RS6612010r1, Goodman describes an initial 8 8 display during power up, followed by ON while it waits for a thermostat call. Seeing ON therefore does not tell you that the burners are heating.

For a dark display on that GMVC96, Goodman’s diagnostic text checks furnace supply voltage, low voltage at the board and the board fuse before condemning the control. Those measurements belong to the technician. Report the dark display. Goodman says to replace the board only after the troubleshooting chart’s other checks have been completed.

The inducer runs, but ignition does not follow

Check 2A sequence observation; service for the missing stage

Describe where the GM9S80 sequence ends

If you hear the inducer but never see ignition through the window, the GM9S80 sequence has not reached the same point as a glowing igniter followed by no flame. Goodman’s sequence places pressure proving and prepurge ahead of igniter operation.

Keep those observations separate when booking service: inducer only, igniter without flame, or flame that disappears. They give the technician a starting point without assuming that every failure to light needs a new igniter.

For the GMVC96 covered by the service manual, Goodman lists restricted intake or flue piping, a disconnected pressure hose, and pressure switch or wiring trouble among the causes of an open low stage pressure switch. Internal hoses and switch tests are service work. Never bridge the switch to make the furnace continue.

A GMVC96 changes speed before it heats

Check 3No adjustment for the normal speed changes

Allow for the two stage sequence

Goodman’s conventional thermostat sequence for this GMVC96 starts the inducer on high speed for a 15 second prepurge. It then steps down to low speed. Igniter warmup begins with that low speed step and closed low stage pressure switch contacts.

That initial speed change is part of the described startup. It should not be mistaken for the furnace abandoning the call for heat.

After ignition, Goodman describes a 30 second blower on delay and another 30 seconds for the circulating blower to ramp to full speed. If the thermostat requests high heat, the control changes the inducer, gas valve and circulating blower to their high stage settings.

If the furnace heats on low stage but the house cannot reach its setting, tell the technician that it produces heat and ask for the high stage request and response to be checked. Keep thermostat wiring and board settings with the installer.

GMVC96: HEAT STAGES AND THE BLOWERALow heatThermostat requestBHigh heatThermostat requestCHeat call endsThermostat satisfiedALow stage continuesGas valve and inducer on lowBHigh stage requestedInducer, gas valve and blower changeCBlower off delayAir keeps moving after the call ends
In the GMVC96 conventional thermostat sequence, low and high heat are separate requests. Airflow also continues after the thermostat ends its heat call.

It warms up, then the air turns cool

Check 4Filter maintenance or service, depending on the sequence

Separate the end of a heat call from a protective stop

For the GM9S80, Goodman says the gas valve closes when the thermostat is satisfied, the inducer continues for a 15 second postpurge and the indoor blower completes its selected off delay. That off delay defaults to 90 seconds in IOG-2030A. Air movement after the flame stops can therefore be expected at the end of a completed call.

On the GMVC96, Goodman also describes a different event: an open limit makes the circulating blower and inducer run until the limit closes. Its possible causes include a dirty filter, restrictive ductwork, blower trouble and other faults. A house still asking for heat while the burners keep stopping needs that distinction investigated.

Goodman requires the same filter type and size when replacing the GMVC96 filter and says never to operate without one. Switch power off before accessing it and refit the filter and any removed door before restoring power.

The GMVC96 drain needs its own investigation

Check 5Condensate service for the GMVC96 described here

Report water trouble with the heat complaint

Goodman’s GMVC96 service instructions say retained condensate can affect combustion. They identify drain hose connections, a dirty furnace trap, incorrect furnace slope and interference from the air conditioning coil drain as things to investigate.

Mention visible water or a recent drain alteration when arranging service. Goodman labels drain tube, trap and drain line inspection and cleaning as qualified servicer work.

The same manual assigns flame sensor cleaning to a qualified servicer. If flame appears and then disappears, include that observation and the control reading instead of opening the burner compartment to clean parts by trial.

What each one takes

Observation Work involved
Silent GM9S80 after a door was removed Correct door fitting, then supply and thermostat checks
Dark GMVC96 display Supply, control voltage and fuse testing before board replacement
Inducer without ignition Pressure proving and ignition sequence diagnosis
GMVC96 heats only on low stage Thermostat request and high stage response checks
GMVC96 water or repeated protective stops Airflow, combustion and drainage investigation

Questions people ask

How often does the GMVC96 filter need attention?

Goodman’s service manual says to clean permanent filters or replace disposable ones every two months, or as required.

Does the fan changing speed mean a failed motor?

The GMVC96 sequence described here deliberately changes inducer speed after prepurge and ramps the circulating blower after its on delay. A speed change alone is not enough to select a motor.

Why does it work again an hour later?

Goodman’s GMVC96 service manual describes an automatic restart attempt after a one hour ignition lockout. It also warns that the furnace returns to lockout if the original condition remains.

What happens when the GMVC96 changes from high heat to low?

In Goodman’s conventional two stage thermostat sequence, the inducer and gas valve change to low stage immediately. The circulating blower stays at high heating speed for 30 seconds before changing to low.

Do these timings cover every Goodman?

No. The GM9S80 figures belong to IOG-2030A, and the GMVC96 figures belong to the conventional thermostat sequence in RS6612010r1. Match the model, control and manual revision before using a timing to judge a fault.

The other furnace guides: Goodman furnace error codes, furnace not igniting, and furnace blowing cold air.

Sources: Goodman *M9S80 & *C9S80 installation manual IOG-2030A, August 2021; Goodman GMVC96/GCVC96 service instructions RS6612010r1, November 2014