Reznor's UDX manual 1034344-0 assigns a flashing 7 on the control display to reversed polarity. The outside status light only shows power and fault status. A flashing L means ignition or flame loss lockout; 5 means an open limit or rollout circuit.
Your Reznor garage heater is blinking, but the light you can see may not be the code display. In Reznor’s UDX manual 1034344-0, the outside LED reports general status. The control inside has a separate display for characters such as 7 and L.
That distinction matters before you look up “seven flashes”. This guide covers the UDX control described in that April 2021 manual, with home garage sizes 030 through 125 in mind. It does not assign those meanings to UDAP, UEZ or a different replacement control.
Before you start
What to carry: a torch, your phone and the heater’s paperwork. Do not balance on stored items to reach a suspended heater.
Gas or electric? Reznor lists natural gas and propane versions in this manual. The rating plate identifies the fuel and model. These are gas unit heater codes, not electric heater fault numbers.
Check the setting, too. Reznor describes the residential sizes as heaters for nonliving spaces. They are not intended for sleeping quarters or as the home’s primary heat source.
Renting? Send your landlord or maintenance contact the model, visible light state and whether the heater starts at all.
For overheating or gas that fails to shut off, Reznor requires the manual gas valve to be shut before the electrical supply. If you cannot safely identify that valve, get urgent help without approaching the heater.
Reznor prohibits gasoline and other flammable vapors or liquids near the appliance. Its burner lights automatically; do not try to light it by hand. Reznor says not to use the heater if any part has been under water. Call a qualified technician immediately to inspect it and replace any gas control that has been under water.
Find out which light you are seeing
Match the model and the kind of signal
Use the model from the paperwork or an already visible rating plate. Then note whether you have a single blinking lamp or a readable character such as L. Reznor’s page 26 describes the outside LED this way:
- Off: no heater power or a control board fault.
- Steady on: the heater is on with no faults.
- Flashing: the heater is on with a fault.
That paragraph does not assign numbered flash groups to the outside light. For UDX, Reznor says viewing the internal character display requires removing the door panel. Leave that access to the service technician; do not open a running cabinet to get a code.
The UDX control display chart
These are Reznor’s table 17 meanings in manual 1034344-0. Read the character and its steady or flashing state together. “Open” and “closed” describe the safety circuit’s state, not a verdict that the switch needs replacing.
| Control display | Meaning in this UDX manual |
|---|---|
| Steady single horizontal bar | Normal operation with no call for heat. |
| Steady 0 | Ignition sequence active. |
| Steady H | Call for heat with a strong flame signal. |
| Flashing 2 | Call for heat with a weak flame signal. |
| Flashing L | Lockout from failed ignition or flame loss. |
| Flashing 3 | Pressure switch has not closed within 30 seconds of the venter motor being energized. |
| Flashing 4 | Pressure switch is closed before the venter motor is energized. |
| Flashing 5 | Limit switch or rollout circuit open. |
| Flashing 6 | Undesired flame. |
| Flashing 7 | Reversed polarity. |
| Display off | Internal fault or power failure. |
What to do with the reading
Give a code 7 to the electrician or heater technician
Reznor labels flashing 7 as reversed polarity. Tell the service company if the problem began after electrical work or a power connection change. Leave wiring tests and corrections to them.
Describe when a pressure code appears
Reznor’s codes 3 and 4 refer to opposite pressure switch states at different points in startup. Note whether you hear the venter start before the heater stops trying. You do not need to reach into the cabinet to make that observation.
Ask the installer to check the venting and pressure circuit against this unit’s instructions. The pressure switch guide explains the circuit’s purpose, but its furnace charts do not replace the UDX table.
Treat code 5 as a safety circuit report
Reznor says the high temperature limit protects against motor failure or restricted inlet or outlet airflow. Reznor warns never to bypass this limit; it will keep shutting the heater down until the cause is corrected. From a safe distance, note any stored objects obstructing the heater’s air path and report them with the code.
For UDX sizes 030 through 125, Reznor also lists a manual reset rollout switch. Its instructions require the cause to be identified and corrected before resetting it, and prohibit bypassing it. Leave that investigation to the technician rather than looking for a reset button.
Keep ignition lockout separate from undesired flame
Reznor’s L entry groups failed ignition and flame loss together. Its 6 entry reports undesired flame. Give the exact character to the service company instead of describing either one simply as “not igniting”.
Use the thermostat for normal heater operation. Reznor requires a 24V thermostat and warns against operating the heater with the line voltage disconnect. On sizes 030 through 125, that method may trip the rollout switch.
What each one takes
| Finding | Work involved |
|---|---|
| Only the outside LED is visible | Record its state and provide the model; arrange access to the control display. |
| Reversed polarity | Electrical testing and correction by a qualified person. |
| Pressure circuit fault | Installer checks of the startup sequence, circuit and venting. |
| Open limit or rollout circuit | Find the airflow or safety problem before restoring operation. |
| Ignition, flame loss or undesired flame | Service of the relevant ignition and flame control system. |
Questions people ask
Does a flashing 2 mean the heater has locked out?
Reznor’s table describes 2 as operation with a call for heat and a weak flame signal. It is a different entry from lockout. Report it even if the heater still produces warmth.
Is a blank control display proof that the board is bad?
No. Reznor lists internal fault or power failure for that state. Those alternatives need to be separated before anyone chooses a part.
Can the technician retrieve earlier faults?
Yes. Reznor’s page 26 says the control stores the last five fault codes and displays them from newest to oldest when power is reapplied. Ask the technician to distinguish that history from the present fault.
Will a UDX lockout clear itself?
Reznor’s fault mode table says a soft lockout resets automatically after one hour. That statement is specific to soft lockout; it is not permission to reset a rollout switch or ignore a returning fault.
Where can I read the Reznor UDX error code PDF?
The Reznor UDX manual saved by this distributor has table 17 on page 26. Check the cover for 1034344-0 and April 2021 before comparing its codes with your installed control.
The other heating guides: Modine Hot Dawg codes, Mr. Heater Big Maxx codes, reading a blinking light, a furnace that will not ignite and rollout switch protection.
Sources: Reznor I-UBX-UBZ-UDX-UDZ installation, operation and maintenance manual (04-21) 1034344-0, pages 1, 3, 25, 26, 27, 28 and 30. Manufacturer document saved from distributor mirror: https://assets.unilogcorp.com/267/ITEM/DOC/Reznor_UDX100_Instruction_Installation_Manual.pdf
By



