Free, independent repair guides
HeatCoolFix

Thermostat Says Hold: Meaning and How to Cancel It

Thermostat Says Hold: Meaning and How to Cancel It
Short answer

Hold means a chosen temperature is taking priority over the schedule. A temporary hold has an ending rule; a permanent hold waits for you to cancel it. The return button depends on the model: Resideo's RTH6360 uses plus or minus, then Cancel; its RTH6350 uses Run Schedule.

If your thermostat says Hold, look at the set temperature and the schedule before treating it as a fault. Resideo’s RTH6350 guide describes Hold as an override that keeps your chosen temperature in place until you resume the program.

The word does not mean the heating must run continuously. It means the temperature target has priority over the programmed changes. Start by deciding whether you want to keep that target or go back to your normal day.

Before you start

What to carry: your phone and the thermostat’s user guide. A torch helps with a small model label. Keep the faceplate fitted; this is a check of the controls you use every day.

Match the model. Read the model number in the app, paperwork or accessible label. Honeywell Home thermostats do not all use the same cancel sequence, as the two Resideo guides below show.

Renting or shared controls? Check who manages the schedule before replacing it with your own settings.

Stay with the user controls. Use the buttons and menus described for your model. Do not disconnect wires, change equipment settings or factory reset a thermostat just to clear Hold. The makers’ cancellation steps below return to scheduling through the normal controls.

Hold, Temporary Hold or Permanent Hold?

ABC A The stored schedule Programmed changes wait while an override applies. B Your manual setting Hold gives this temperature priority over the program. C How the override ends Next period, a chosen time or a manual cancellation.
A temporary override ends according to its model's timing rule. A permanent override waits for you to resume the schedule.

Resideo’s RTH6360 guide distinguishes the two: changing the setpoint creates a Temporary Hold until the next scheduled period, while selecting Hold during that adjustment changes it to Permanent Hold. On the RTH6350, the permanent version is simply called Hold.

Sensi’s Smart Thermostat guide adds an important difference. Its temporary setting lasts until the next scheduled setpoint with a minimum hold of two hours. Do not assume every thermostat returns to the schedule at the very next change.

Check 1

Read the ending rule as well as the word Hold

Look for an end time or a label such as Temporary Hold, Permanent Hold or Temporarily Set To. Compare it with the user guide for your exact model.

For ecobee Smart Thermostat Premium, the user guide says a manual temperature adjustment creates a hold governed by the selected Hold Action. That preference can explain why a change lasts longer than you expected.

If you want the chosen temperature to remain, you may have nothing to cancel. If you want the daily program back, use the matching controls below.

Honeywell Home: two different return buttons

Check 2

RTH6360: press plus or minus, then Cancel

Resideo’s RTH6360 quick guide gives the same cancellation sequence for Temporary Hold and Permanent Hold: press the plus or minus button, then press Cancel.

You do not need to erase the schedule to undo that choice.

For the RTH6350, RTH6450, RET93E and RET95E series, Resideo’s separate operating manual says to press Run Schedule. That cancels either the temporary setting or the Hold and resumes the program. Use this sequence only for the models that manual covers.

If the screen is blank or the equipment does not respond after you have chosen the right mode and setpoint, move to Honeywell thermostat not working. That is a different check from removing a schedule override.

ecobee: check Hold Action

Check 3

Smart Thermostat Premium: cancel the hold box

ecobee’s Smart Thermostat Premium guide says to tap the X at the right of the hold box on the thermostat, or Cancel in the app. Cancelling resumes the schedule.

For that guide’s interface, Hold Action is under Main Menu System, Main Menu General, Settings, Preferences. Its choices include two hours, four hours, Until the Next Scheduled Activity, Until I Change It, and Decide at the Time of Change.

Choose the duration that suits the way you use the thermostat. If your interface has different menu names, use its matching guide rather than looking for a Honeywell button.

The ecobee guide also lists app and connected assistant changes as ways to create a hold. If one comes back, check whether somebody changed the temperature remotely before changing the schedule itself.

Sensi and White-Rodgers

ABC A Match the model RTH6360: plus or minus, then Cancel. RTH6350 uses Run Schedule. B Read the right control White-Rodgers 1F80-361 returns to its program with Run. C Check the result Compare the target with the current schedule period.
The words on the control matter. Run Schedule, Cancel and Schedule On belong to different interfaces.
Check 4

Sensi Smart Thermostat: return Schedule to On

Copeland’s Sensi Smart Thermostat manual says Schedule Off holds one temperature in the selected system mode. Turning Schedule back On returns control to the program.

For an active temporary hold, Sensi’s support instructions say to toggle Schedule Off, then On at the thermostat. In the Sensi app, tap the X in the hold square and confirm with OK.

Keep this wall control sequence to the Sensi Smart Thermostat discussed here. Match a Touch, Touch 2 or Lite to its own operation guide.

For the White-Rodgers 1F80-361, Copeland’s instructions say the Hold button starts an indefinite temperature hold and Run starts program operation again. That is a button press, not an instruction to enter the configuration menu.

Google Nest: check the generation

Check 5

Nest Thermostat or Learning Thermostat fourth generation: end the hold

Google’s Hold temperature instructions apply to the Nest Thermostat and Nest Learning Thermostat fourth generation. In the Google Home app, select the thermostat, open Hold temperature and tap End hold in the same heating or cooling mode as the hold.

At the thermostat, Google’s instructions use Hold in the menu, then Stop. The page explicitly excludes Nest Thermostat E and Learning Thermostat third generation or earlier from this Hold temperature feature.

If yours is one of those earlier models, do not search its menus for this newer control. Identify the model before using a different Nest scheduling instruction.

What each one takes

What you want What the job involves
Resume today’s schedule A user control change using the button named in your model’s guide.
Keep a different temperature briefly Choose a temporary override and check its ending rule.
Keep one temperature indefinitely Choose the model’s indefinite hold or scheduling preference.
Change what happens every day Edit the stored schedule using your model’s instructions.
Find why a hold returns Check manual changes and app activity before replacing equipment.

Questions people ask

Does Permanent Hold mean the thermostat is locked?

For the Resideo RTH6360, it is a schedule override that the user can cancel. Read the screen’s exact wording before treating a separate lock message as the same thing.

Why did the schedule stop after I changed the temperature?

That is how the ecobee Premium guide describes a manual adjustment: it creates a hold. Its Hold Action preference decides the duration.

Will Temporary Hold end after an hour?

There is no single time across these models. The RTH6360 uses the next scheduled period; the Sensi Smart Thermostat also has a two hour minimum.

Why did cancelling Hold give me a different temperature?

Resideo says cancellation resumes the programmed schedule on the RTH6350 series. Check the target stored for the current period if that is not the temperature you want.

Should I reset it if the schedule is wrong?

Start with the user guide’s schedule controls. For a separate frozen screen or reset problem, use the thermostat reset guide to distinguish restart and reset choices.

The other thermostat guides: thermostat not working, aux heat on the thermostat and Sensi thermostat not working.

Sources: Resideo RTH6360 quick installation guide 33-00201EF and RTH6350/RTH6450/RET93E/RET95E operating manual 33-00116ES; ecobee Smart Thermostat Premium installation and user guide, Hold settings; Copeland Sensi Smart Thermostat manual operation guide and End the Temporary Hold support; White-Rodgers 1F80-361 instructions 37-6621; Google Home and Nest Help, Hold the temperature on your thermostat