On the MHU50, MHU80 and MHU125 control in Mr. Heater's 2019 manual, two green flashes mean ignition lockout, three mean a pressure switch fault, four mean an open limit or rollout switch, and five mean flame sensed with the gas valve off. A steady light has a separate meaning.
Mr. Heater Big Maxx error codes need the whole light pattern. Two flashes and a pause are different from a light blinking continuously. Mr. Heater’s 2019 MHU manual also gives separate meanings for a light that stays on and one that stays off.
This guide follows manual 60185 for MHU50, MHU80 and MHU125. Match that model list and the ignition control information supplied with your heater before using the chart. It covers garage unit heaters; it does not translate portable Buddy heater messages or an unrelated display’s E1 code.
Before you start
For a gas smell, Mr. Heater says to leave the building immediately without trying to light the appliance, touching an electrical switch or using a phone inside. Call the gas supplier from a phone away from the building. Follow its instructions; call the fire department if you cannot reach it.
CPSC says a sounding CO alarm calls for fresh air outside and an emergency services call. Account for everyone and wait for responders’ permission before returning. If a faulty appliance caused the alarm, CPSC says it must stay unused until trained personnel have serviced it.
Mr. Heater requires a qualified installer, service agency or gas supplier for service. Its maintenance warning requires both gas and electrical power to be off before work starts. Mr. Heater also says to follow its lighting instructions when returning the unit to operation after service. Keep gasoline and other flammable liquids or vapors away, as its cover warns.
What to carry: your phone, a torch and the model number from your paperwork. Observe only from a secure position without opening a running heater. If the LED cannot be seen safely, have the technician read it.
Gas or electric? This MHU manual describes a gas burner with automatic ignition. Mr. Heater expressly says not to light its burners by hand.
Renting? Give maintenance the model and the complete light pattern. A different make needs its own chart, such as the Reznor unit heater guide.
Read the green LED, including the pauses
Separate continuous blinking from a counted code
Mr. Heater calls this the ignition control LED. Table 3 on printed page 11 identifies it as green. Note whether it blinks slowly throughout, blinks quickly throughout, repeats a small group, stays dark or stays lit.
In this table, slow flashing is normal with no call for heat. Mr. Heater also notes slow flashing when the thermostat is in continuous fan mode. Fast flashing is its normal call-for-heat indication. Those descriptions are different from the two-flash lockout row.
The MHU50, MHU80 and MHU125 code list
These entries follow Table 3 in Mr. Heater’s 2019 manual 60185 PDF, hosted by Lowe’s. CAB in the manufacturer’s table means the combustion air blower.
| Green LED | Meaning in this manual |
|---|---|
| Slow flashing | Normal operation, no heat call; also noted for continuous fan mode |
| Fast flashing | Normal operation, heat call; the row lists a FLAME terminal signal of 0.6 to 1.0 microamps |
| 2 flashes | System lockout: failed to detect or sustain flame; the row lists a signal below 0.6 microamps |
| 3 flashes | Pressure switch closed before the combustion air blower is energized, or open after it is energized |
| 4 flashes | High limit or rollout switch open |
| 5 flashes | Flame sensed while the gas valve is not energized |
| Steady off | Loss of power; the table also directs a check of the board’s 3 amp fuse |
| Steady on | Ignition control failure |
The current readings are technician measurements, not an instruction to put a meter inside the heater.
Two flashes: failed to detect or keep a flame
Describe what happened before lockout
Mr. Heater’s two-flash wording covers both failure to detect flame and failure to sustain it. Tell the repairer whether the heater never appeared to light or whether it warmed briefly and stopped. That observation helps explain the complaint without choosing a replacement part from the code alone.
The manual’s failure-to-operate list starts with a thermostat heat call and includes electrical supply, gas supply and ignition lockout. You can check the thermostat setting and report a known supply interruption. Leave gas valves, wiring and internal testing to the service agency.
For this control, Mr. Heater describes an automatic retry after a 60-minute ignition lockout. It also describes interrupting that period through the thermostat. If the unit locks out again, Mr. Heater says to call a service technician.
Three flashes: pressure switch state and blower timing
Report whether the combustion blower starts
Mr. Heater’s three-flash entry has two branches: the pressure switch is closed too early, or it remains open after the combustion air blower is energized. The sequence of operation says this switch proves blower operation before ignition is allowed.
From outside the cabinet, note whether you hear the small exhaust blower start. Report an obviously obstructed vent outlet if you can see it from ground level. Mr. Heater names an obstructed flue as a cause of pressure-switch shutdown.
The manual says this pressure switch is factory set and needs no field adjustment. Have the technician handle the pressure tubing and blower port inspection described in its service information. Do not bridge the switch to make the burner run.
Four or five flashes: leave the safety diagnosis to service
Give the exact safety code when booking the repair
For four flashes, Mr. Heater names either an open high limit or an open rollout switch. Its rollout section says to check adequate combustion air before a manual reset. That condition is a reason to leave the reset button to the technician, rather than treating it as a restart control.
Five flashes has a different meaning: Mr. Heater says flame is sensed while the gas valve is not energized. Keep the heater out of use pending service for that condition. It is not the two-flash failure to prove flame.
The manual also says the limit control is factory set and not field adjustable. A service visit should identify which protection opened and why before returning the heater to use.
What each one takes
The work below follows the MHU manual’s code and service sections. It is a guide to what to discuss with the repairer.
| Reading | Work involved |
|---|---|
| 2 flashes | Supply, ignition and flame-signal checks |
| 3 flashes | Blower, pressure circuit and flue inspection |
| 4 flashes | Identifying the open limit or rollout protection and its cause |
| 5 flashes | Investigating a flame signal with the gas valve not energized |
| Steady off or on | Power, fuse or ignition-control diagnosis appropriate to the light state |
Questions people ask
What does Big Maxx error code 2 mean?
If you mean two green LED flashes on the control covered here, Mr. Heater defines it as system lockout from failure to detect or sustain flame. It is not a diagnosis of a bad flame sensor by itself.
Where is the Big Maxx error codes PDF?
The linked manufacturer manual contains Table 3 on printed page 11.
Does E1 mean the same thing as one flash?
Table 3 does not list E1 or a numbered one-flash fault. Record which device displays E1 and use that device’s model-specific instructions instead of converting it into this LED chart.
Does a dark light mean the ignition board has failed?
Mr. Heater’s steady-off entry points to power loss and a fuse check. Its ignition-control-failure entry is steady on.
Can the heater fan run without a heat call?
Mr. Heater’s table includes continuous fan mode and says the LED flashes slowly in that mode. Check the thermostat’s fan selection before describing slow flashing as a burner fault.
For related explanations, read ignition problems, what flame sensing does and why rollout protection matters. Use this MHU manual for the unit heater’s actual service procedure.
Sources: Mr. Heater Operating Instructions and Owner's Manual 60185, 2019, MHU50/MHU80/MHU125, cover and printed pp. 11 to 12, manufacturer PDF hosted by Lowe's; CPSC Carbon Monoxide Questions and Answers, saved archive text.
By



