Navien's NCB-H and NFC-H manuals separate a tap with no flow from water that flows cold. They also say room heating pauses during domestic hot water production. Check which service is missing, the front panel power and the appropriate temperature setting before arranging filter or system work.
A Navien combi boiler with no heat or hot water can leave you wondering which half of the system has stopped. Navien’s NCB-H and NFC-H troubleshooting tables start by separating no water flow, cold flowing water and a space heating problem.
This guide follows those owner checks when there is no error code. If a number appears, use the Navien boiler error code guide. The separate Navien tankless water heater codes page covers NPE water heaters, rather than the combi models here.
Before you start
What to carry: a torch and the model information from your boiler paperwork. You can make the checks below without opening the cabinet or draining anything.
Gas or electric? Navien identifies the NCB-H as a gas burning combi boiler. These checks cover the NCB-H and NFC-H combi models named here.
Renting? Pass the model and which service is missing to whoever handles heating repairs.
Overheating or gas that will not shut off. Navien’s NCB-H manual says to close the manual gas valve. Do not use repeated power cycling as a remedy for overheating.
A smell of gas. Navien says not to light an appliance, touch an electrical switch or use a phone in the building. Leave, call the gas supplier from outside and follow its instructions. If the supplier cannot be reached, call the fire department.
If any part of an NCB-H has been under water. Navien says not to use it, to contact a qualified service technician immediately and that the boiler must be replaced.
Hot water. Navien warns that increasing the domestic water setting increases scalding risk. Its NCB-H instructions call for the lowest setting that provides comfortably hot water. Keep people away from the test tap and check the water carefully before use.
Separate the two services first
Check power and the right temperature setting
Navien’s NCB-H troubleshooting table asks whether the boiler has power or is in standby. It directs the user to ensure it is powered and turned on with the front Power button. Navien also warns that the NCB-H must be filled with water before you turn it on. If you cannot confirm that, leave startup to the technician.
The same manual provides separate space heating and domestic hot water temperature settings. If the taps are too cool, inspect the domestic setting. If the rooms are cold, inspect the heating setting and the room thermostat’s demand. Do not raise the tap water temperature to solve a room heating problem.
Navien’s NCB-H display key identifies separate domestic hot water and space heating demand indicators. Watch whether the appropriate demand appears when a hot tap is opened or the house calls for heat. Tell the repairer if the requested service never appears on the display.
No hot water: is there any flow?
A dry tap needs a different check from a cold tap
For no water coming out, Navien’s NCB-H table asks about its domestic cold inlet filter and possible freezing. It also tells the owner to ensure the shutoff valves on the hot and cold water pipes are open. Identify them from the installation labels or paperwork; do not turn an unidentified valve.
For water flowing but staying cold, Navien asks whether the tap is open enough to draw at least 0.5 gallons per minute through the NCB-H. Try opening the hot side farther, keeping clear of the outlet because the water may heat. Tell the repairer whether that changes the result.
Navien’s NFC-H user table gives the same 0.5 GPM check for its cold flowing water symptom. That is a check for these models, rather than a flow figure to apply to every Navien product.
Compare another hot tap and report whether the problem affects one outlet or the whole house. If water is flowing normally but remains cold, do not describe it as a blocked tap when booking the visit.
Hot water works, but the rooms stay cold
Finish the hot water demand, then watch heating
Navien says the NCB-H’s space heating side does not work while the unit is heating domestic hot water. Close the test tap, then check the heating demand and whether the rooms begin warming. The NFC-H troubleshooting table describes the same priority behavior.
If the heating remains absent, Navien’s NCB-H table points to its heating temperature setting, power and a restricted heating side filter. Send those observations with the service request. For a room thermostat that is blank or does not call, use thermostat not working.
Keep the two filters straight
Navien’s NCB-H manual has separate procedures for its domestic cold water filter and heating return water filter. Its troubleshooting table ties the first to a tap with no flow and the second to a heating side malfunction.
Navien says to drain the heating side before removing its return filter, and the hot water side before removing its cold inlet filter. Do not unscrew a filter as a quick check on a hot, pressurized boiler. Ask the service person to follow the correct draining, cleaning and return to service procedure for your model.
After the outside checks
Navien’s NCB-H troubleshooting section allows a front panel Back button reset for minor problems. It directs unresolved problems to an authorized technician, licensed professional or technical support. A missing heat call, restricted water flow and a frozen boiler still need their own causes resolved.
Ask the repairer to demonstrate both a hot tap and a room heating call before leaving. Include whether the fault started after maintenance or a change to the controls, and whether either service still works.
What each one takes
| Finding | Next work |
|---|---|
| Front panel off or wrong service setting | An owner setting check |
| No flow at hot taps | Water valve identification, then filter or freezing investigation |
| Cold water at a very small hot tap flow | The named model’s flow check |
| Rooms pause during a hot water draw | Check whether heating resumes after that demand ends |
| Restricted heating return filter | Draining and maintenance following the NCB-H procedure |
Questions people ask
Does a clear display mean the boiler needs no repair?
No. Navien’s NCB-H manual gives its basic symptom checks separately from the error code chart. The absence of a code does not replace the flow, power and service checks above.
Will an NCB-H restart after a power failure?
Navien says it automatically returns to normal operation when power is restored, without a manual reset. If yours remains off, report the panel’s condition along with the other observations.
Should I unplug it while waiting in freezing weather?
Navien says the NCB-H freeze protection function needs electricity and cautions against unplugging it except for routine maintenance. If it cannot operate safely, arrange a professional freeze protection plan rather than relying on the boiler alone.
Where can I find the readings the technician asks for?
Navien’s NCB-H display key identifies system pressure, the two set temperatures and demand indicators. Use those front panel readings; you do not need to open the cabinet to gather them.
Can I use these button instructions on an NCB-E?
Use its own manual. This page’s Back and Power button instructions come from the NCB-H manual. The Navien boiler guide separates the control families.
The other boiler guides: boiler not working, boiler pressure, and zone valve not working.
Sources: Navien NCB-H User's Information Manual, sections 1, 2.4, 3, 4.1, 4.3, 4.4 and 5.1; NFC-H User's Information Manual, section 5.1. Manufacturer PDFs saved in data/sources/navien-combi-no-heat.
By



