Free, independent repair guides
HeatCoolFix

Carrier Thermostat Error Codes: E1, E3, E4 and Dashes

Carrier Thermostat Error Codes: E1, E3, E4 and Dashes
Short answer

Carrier's Performance AC/HP control manual defines E1 as lost communication between its display and equipment control modules. It lists no E2 message. Its E3 outdoor sensor condition appears as dashes in the outdoor temperature position, while E4 means internal memory failure. These meanings belong to the named Performance models.

Carrier thermostat error codes need the thermostat model beside them. Carrier’s Performance AC/HP manual gives E1 a specific meaning: the display and equipment control modules cannot communicate through their two wire connection. That is different from looking up a furnace fault on the wall screen.

This guide covers the Performance TP-PAC, TP-PHP, TP-NAC and TP-NHP controls in TP-PAC-07SI, plus the separate Comfort meanings identified below. If the screen is blank or the trouble is Wi-Fi, use Carrier thermostat not working.

Before you start

What to carry: a torch and the thermostat model from your paperwork. Photograph the whole display so the repairer can see where the message appears, along with any normal temperature still shown.

Renting? Send that information to the person who arranges the heating repairs. You do not need to remove the wall control to collect a visible message.

The code is information for a repair, not permission to change wires.
Carrier’s Performance instructions require all equipment power to be turned off before installation and warn of more than one possible disconnect. Leave terminal measurements, module wiring and replacements to the installer.

Carrier says the Performance control’s V+ and Vg wires carry a combination of power and communication data unique to these products. They are not ordinary 24VAC connections. Do not move them to conventional thermostat terminals or jumper them to test a code.

Read the message in its place on the screen

PERFORMANCE: WHICH TEMPERATURE IS MISSING?Room temperature- -Outdoor temperature- -ABCARoom temperatureRoom sensing fault.BOutdoor temperatureMissing reading when needed.CAveraging configured?A working room sensor can take over.
Carrier's Performance manual distinguishes a room temperature reading from the outdoor temperature position. The dashes below are schematic examples, not an actual screen layout.
Check 1A reading check; no parts to buy

Keep the control family and display position together

Use the model and document family in the tables below. The TP Performance and TC Comfort manuals have separate error sections. A matching brand name does not make their lists interchangeable.

For the Performance family, Carrier describes a failure to read room temperature using dashes in that temperature display. Its E3 entry describes dashes in the outdoor temperature location when an outdoor reading is needed for operation but cannot be read properly.

Do not describe every pair of dashes as a failed outdoor sensor.

Performance AC/HP messages from TP-PAC-07SI

Carrier gives the following meanings for the four Performance models named at the top. Keep the limits in the middle column when comparing your screen.

Entry in Carrier’s manual What it describes Repair direction
Dashes at room temperature The control cannot properly read room temperature Investigate room sensing; see the averaging exception below
E1 Display Module and Equipment Control Module cannot communicate through the two wire connection Installer diagnosis of that module connection
E2 The manual explicitly lists no E2 error message Do not assign another control’s E2 definition
E3 entry Outdoor temperature cannot be read when needed; dashes appear in the outdoor temperature location Check the outdoor sensing arrangement
E4 Internal memory failure Carrier directs replacement of the AC/HP control
Check 2A connection diagnosis before choosing replacement parts

For E1, identify the two modules involved

Carrier’s Performance manual allows a two piece installation with the Display Module at the wall and a separate Equipment Control Module. Its E1 definition concerns communication between those two parts. It is not a Wi-Fi password diagnosis.

Tell the installer if the fault began after a thermostat or module replacement. Carrier says a failed display or equipment control module should be replaced as a matched set, with the same model and serial number on both parts. Mixing parts can make some setup functions appear and others disappear.

Leave access to that second module and the wiring tests to the installer. The visible E1 does not identify which module or connection has failed.

Check 3Sensor diagnosis; the installed sensing arrangement matters

For a sensing message, report any alternating temperature

Carrier’s Performance manual gives an exception to its room sensing shutdown behavior. If the installer has selected averaging of the local and remote room sensors, the display alternates between dashes for the failed sensor and the working sensor’s temperature every ten seconds.

In that configured case, Carrier says the control continues operating from the working sensor. Otherwise, its room temperature fault entry says outputs turn off, except the fan if it was on. A fan still running does not clear the sensing fault.

Do not unplug a remote sensor to see what changes. Describe whether the screen alternates and whether the missing reading is indoors or outdoors.

Comfort controls use a shorter list

Carrier’s TC-PAC-06SI instructions cover TC-PAC, TC-PHP, TC-NAC and TC-NHP. Their error section identifies two messages: dashes for room sensor failure and E4 for internal memory failure. Carrier specifies thermostat replacement for either confirmed failure in that manual.

Check 4A control replacement visit, after the message is confirmed

For E4, arrange the model's replacement assessment

Carrier’s Performance manual also directs replacement for E4. Its separate TC-PAC01-A and TC-PHP01-A owner manual says a memory failure returns that thermostat to factory settings and tells the owner to contact the heating and cooling dealer.

If settings changed when the message appeared, include that detail with the model. The thermostat reset guide explains why a reset and a repair are separate choices.

PERFORMANCE E1: THE MODULE CONNECTIONDisplay ModuleEquipment ControlABCADisplay ModuleThe wall interface.CV+ and Vg linkCarries power and data.Not ordinary 24VAC wiring.BEquipment Control ModuleInstaller access and diagnosis.
The E1 link in Carrier's Performance manual joins the Display Module and Equipment Control Module. The V+ and Vg connection carries power and data; this drawing is not a wiring instruction.

If your code is EF, 178 or 179

The tables here do not assign meanings to EF, 178 or 179. Give the installer the complete wording and control model so the message can be matched to its own Carrier document. Do not choose a sensor or control board from a similar number in this list.

For faults originating in a furnace or outdoor unit and reported at an Infinity control, the separate Carrier Infinity system code guide covers its named equipment. It also keeps identical numbers separate when different equipment gives them different meanings.

What each one takes

Confirmed condition Work involved
Performance E1 Module communication diagnosis and matching any replacement parts
Performance room sensor fault Checking the configured local and remote sensing arrangement
Performance outdoor temperature missing Outdoor sensing diagnosis when that input is needed
E4 on the named Performance or Comfort controls The replacement directed by the applicable Carrier manual

Questions people ask

Does E1 always mean a room temperature sensor?

No. Carrier’s TP-PAC-07SI defines it as lost communication between two modules. Use the definition for your model instead of applying a brand wide E1 meaning.

Why does the table include E2 if it has no meaning?

Carrier explicitly says there is no E2 error message in TP-PAC-07SI. That prevents a reader from treating another thermostat’s E2 description as a confirmed fault on these controls.

Is the E3 entry supposed to show the letters E3?

Carrier’s entry says the display indicates dashes in the outdoor temperature location. That screen behavior, including the need for an outdoor reading, is part of the definition.

Can a Performance control still heat with a sensor fault?

Carrier describes continued operation from the working sensor when local and remote room sensor averaging is configured. That specific exception is explained in check 3.

Should I use these tables for a blank screen?

No. Start with the Carrier power and screen checks. This guide interprets visible messages on the named controls.

The other thermostat guides: thermostat not working, thermostat batteries, and thermostat wiring.

Sources: Carrier Performance Series AC/HP Thermostat Installation Instructions TP-PAC-07SI, TP-PAC, TP-PHP, TP-NAC and TP-NHP, printed pp. 3, 9, 46 to 47; Comfort Series AC/HP Thermostat Installation Instructions TC-PAC-06SI, TC-PAC, TC-PHP, TC-NAC and TC-NHP, printed p. 23; Comfort Series TC-PHP01-A and TC-PAC01-A Owner's Manual OM-TCPHPA-02, printed p. 48.