An A.O. Smith tank with no hot water needs a different check from one that runs out early. For the conventional electric and atmospheric gas models covered here, start with supply, recent installation work and the control state. A tripped electric temperature limit needs its cause repaired before power returns.
An A.O. Smith water heater that never gets hot and one that gives a short hot shower need different investigations. Tell the person checking it which problem you have, especially if it started just after installation or draining.
A.O. Smith’s conventional electric manual puts lost power, a burned upper element and the temperature limit on its no hot water list. Its atmospheric gas manual starts somewhere else: the status light and pilot.
Before you start
What to carry: a torch and your phone for the model number, gas control position and any light pattern. The first checks below leave the covers fitted.
Gas or electric? This guide uses A.O. Smith’s 100309797 electric manual, linked for the ProLine ENS-50 110, and 100263112 atmospheric gas manual, listed for models including GCR-50. Match your model and supplied manual before using either branch.
Vertex or hybrid? Use the separate Vertex fault message guide or A.O. Smith heat pump code guide. Their controls are outside this conventional tank guide.
Renting? Send maintenance the model and symptom before arranging repairs.
For gas overheating or a gas supply that fails to shut off, A.O. Smith says to close the heater’s manual gas control valve and seek qualified assistance. Its electric manual says an opened ECO needs the overheating cause identified and repaired before power returns.
Both A.O. Smith manuals require replacement of the entire heater after flooding or if its thermostats have been submerged.
Both manuals warn that hot water can scald, even at 120 degrees F. Do not raise the temperature as a test. Keep electrical covers fitted and leave exposed wiring tests to someone qualified to perform them.
First separate the heater from the shower
Compare more than one hot tap
A.O. Smith’s two manuals both tell you to compare temperatures at several faucets. A faulty mixing valve in a shower or faucet can reduce delivered hot water even when the tank has plenty.
If the kitchen gets hot and only the shower stays cool, report that difference before ordering a heater part. The house hot water guide follows that delivery problem further.
If every tap is affected, distinguish water that stays cold from hot water that runs out early. A.O. Smith lists high demand, plumbing leaks and reversed connections among shortage causes in these manuals. That leaves more to check than the thermostat alone.
Electric tank: check the history and supply
Tell service if it has never heated since installation
For the electric tanks covered by 100309797, A.O. Smith lists no electrical power and a dry fired upper element among installation related causes of no hot water. It also lists reversed inlet and outlet connections, an upper thermostat or wiring fault, and a hot plumbing leak.
Look at the labelled breaker state without taking the heater apart. A breaker handle alone does not establish that the heater is receiving power: A.O. Smith’s next diagnostic is a supply check at the heater.
That check exposes electrical connections, so leave it to an electrician or qualified service person. If the heater was drained or newly installed, tell them whether power may have returned before the tank was full. A.O. Smith identifies that sequence as dry firing.
Electric tank: no heat versus reduced capacity
Keep the ECO and element symptoms separate
In 100309797, A.O. Smith says a failed upper element leaves no hot water. A failed lower element or lower thermostat can leave some hot water, but less than before. Those clues help direct testing; they are not a reason to buy both elements without testing.
The same manual says the Energy Cut Off, or ECO, interrupts element power if tank water gets too hot. A.O. Smith requires a qualified person to investigate an ECO trip and repair the cause before restoring power. Repeatedly pressing the red button skips that investigation.
Our element guide explains the component, and the thermostat guide explains its control.
Atmospheric gas tank: let the light choose the branch
Read the light before trying another lighting attempt
For the atmospheric gas family in 100263112, A.O. Smith says one status flash every three seconds indicates a lit pilot with no problem detected by the gas control. With that pattern and no hot water, its first direction is to check that the control knob is at HOT.
If the light is dark, A.O. Smith directs you to the lighting instructions on page 23. Follow the instructions attached to your tank, including their gas safety checks and waiting period. Before lighting, A.O. Smith requires an intact viewport, a completely full tank and the gas type shown on the data plate. The manual requires 10 minutes between lighting attempts. After three unsuccessful attempts, turn the knob to OFF and use its no hot water troubleshooting section.
If you have already followed that sequence, tell service whether a spark was visible through the viewport and whether the pilot caught. A.O. Smith’s next checks separate no spark from a spark with no pilot, and refer an unsuccessful pilot lighting attempt to a qualified person.
For flashes more frequent than the normal pattern, use the status chart on page 27 of this manual. A light that goes out again belongs in your service report; do not bypass a safety switch to keep the burner running.
When it heats, but the hot water does not last
Describe what changed before changing the setting
A.O. Smith’s gas manual lists excess demand, reversed plumbing, a damaged dip tube, hot plumbing leaks and sediment or lime for insufficient hot water. If the shortage began with a new installation, ask the installer to check the connections before blaming tank size.
For an existing gas tank with reduced output, A.O. Smith says sediment or lime may reduce efficiency. Its plumbing leak discussion also describes a burner running almost continuously while little hot water is available.
The electric manual adds low supply voltage and a lower element fault to its shortage list. Tell service whether the tank heats after quiet periods, struggles only during several uses, or has lost capacity under the same routine as before.
What each one takes
| Finding | What the next job involves |
|---|---|
| Only one fixture is cool | Checking its mixing control before changing heater parts. |
| Electric tank never heated after installation | Supply, filling history and upper element diagnosis. |
| Electric ECO has tripped | Qualified overheating investigation and repair before power returns. |
| Gas status light is dark | The matching lighting sequence, then service if it fails. |
| Heat is available but capacity has fallen | Demand, plumbing and model specific heating checks. |
Questions people ask
Why can a new gas pilot be slow to light?
A.O. Smith says a newly installed heater has air in the gas line, which may take several lighting attempts to clear.
Does a flashing light guarantee hot water?
The normal flash in 100263112 tells you about the pilot and control, while the manual still asks you to check the control position if there is no hot water.
What does a solid gas status light mean?
In 100263112, A.O. Smith says a solid status light means the pilot was lit but is now off.
Can the tank be working when the shower is cold?
Yes. Both cited manuals describe a faulty fixture mixing valve delivering cooler water despite hot water in the tank.
Should I order a thermostat first?
The electric manual also lists power, element, ECO, plumbing and wiring causes. Ask which test identifies the failed part before approving a replacement.
The other water heater guides: water heater not working, no hot water in the house and water heater pilot light.
Sources: A.O. Smith residential electric manual 100309797, pages 17 to 19, linked for ENS-50 110; residential standard gas manual 100263112, pages 23 to 27, linked for GCR-50 in the residential gas manual index; both manuals: safety instructions
By



