For a Rinnai tankless heater with no code, separate a heater switched off at its controller from one that fails to respond to water flow. Named RU, RUR, RE and V manuals cover flow, controls and water connections. Filter service and internal tests belong to a qualified professional.
When your Rinnai tankless heater stays quiet after you open a hot tap, look at the controller before reaching for a reset. Is it switched on, does it show a temperature, and does its operating light change with the water running?
This guide follows Rinnai’s checks for no hot water without a fault code. If a number or message is flashing, use Rinnai tankless error codes instead.
Before you start
What to carry: your phone and a torch for the label and controller. Keep a picture of the model label and a description of the display with your service notes.
Gas or electric? These are gas tankless heaters with an electrical supply. The examples come from Rinnai’s RU199i, RUR199i, RE199i and V75i manuals. An electric tankless heater uses a different procedure.
Find the matching document. The manuals saved for this guide are linked from Rinnai’s RU199iN, RUR199iN, RE199iN and V75iN pages. Do not transfer an RUR pump indication to an older V controller.
Renting? Give maintenance the model and what happens when a hot tap opens. Leave heater repairs with them.
Rinnai says the temperature controller does not disconnect electrical power. Its RE maintenance instructions require electrical power, gas and incoming water to be shut off before maintenance, and reserve that work for a trained, qualified professional. Keep the case fitted and do not unplug internal components to test a blank screen.
For overheating or gas that fails to shut off, the cited Rinnai manuals say to close the manual gas control valve.
The cited Rinnai manuals say not to use a heater if any part has been under water. Immediately call a qualified professional to inspect it and replace submerged controls.
The RU and RUR manuals warn that hot water can scald. Feel water carefully before bathing and do not turn the setting higher to force the burner to light.
Check the controller state before the water side
Separate Off, no power and a locked setting
Rinnai’s RU and RUR operation sections say to press On/Off if the water heater is off. For the indoor models covered here, the operating buttons are on the front of the heater. Leave an outdoor unit’s panel access to someone following its own instructions.
For multiple controllers, Rinnai says the Priority light identifies the controller that can set the temperature. Change priority only while no hot water is running. A setting that will not change can therefore need a controller check rather than a new heating part.
The RU manual also provides a controller lock. Ask whether that was enabled if the display works but adjustments are unavailable.
If the display stays blank, check only accessible external supply observations: whether the indoor cord is plugged in and whether the labelled circuit is switched off or tripped. Rinnai specifies a grounded electrical supply for these gas heaters. Leave outlet and internal electrical testing to service.
Try one hot tap and watch what changes
See whether a fuller hot draw changes the response
Rinnai’s RU and RUR operation instructions explain that flow near or below the minimum can leave water cold or alternating hot and cold. Open one hot tap farther and watch whether the heater responds. Compare that result with the fixture where you noticed the fault.
Use the activation flow in your model’s specification, rather than a number borrowed from another series. The RU no code row starts with confirming sufficient flow; the RE and V no code rows also include it.
If the heater responds only at the stronger draw, explain that pattern to service. If it still does nothing, service needs to check the power supply, inlet filter and flow sensor. A silent heater does not identify a failed igniter by itself.
When it gets warm, but not comfortably hot
Check the set temperature and how much cold water is being mixed
For RU and RUR models covered here, Rinnai says a temperature closer to what is actually used at the faucet can reduce the cold water mixed there. Its instructions recommend reducing a high setting when that setting contributes to poor operation at low hot water flow.
That is a reason to compare the displayed setting with how you use the tap, not an instruction to raise it.
If only one fixture misbehaves while another provides hot water, give that comparison to the plumber. For the broader delivery checks, see no hot water in the house.
What the no code service visit should check
Include the filter, installation history and plumbing
Rinnai’s RU, RE and V no code lists include the inlet water filter and reversed hot and cold connections on new installations. Tell the installer if this heater has never supplied hot water since the plumbing was connected.
In the RE maintenance section, Rinnai describes closing both water isolation valves, catching the retained water in a bucket, rinsing the filter and refitting it before reopening the valves. The section reserves maintenance for qualified professionals and gives the supply shutdown precautions stated above.
The RE and V diagnostic lists go beyond the filter to plumbing crossover, the turbine and the flow sensor. These are service checks. In particular, the V manual labels its crossover and internal electrical work for a licensed professional only.
For a blank display accompanied by clicking, the RE chart includes a water flow servo investigation. Describe the clicking to service; the chart’s instruction to disconnect the motor is not an owner reset procedure.
RUR pump lights and unexplained beeping
Describe the light or sound precisely
For the RUR models in 100000508, Rinnai lists a solid In Use light for ignition and water flow, a slow flash for ignition with pump operation, and a rapid flash for pump operation without ignition. Report which indication appears when you are drawing hot water.
For beeping, first distinguish a sound when a key is pressed from an ongoing alarm. Rinnai’s RU control section has a mute setting specifically for keypress beeps. That feature does not identify the cause of an unexplained alarm or loss of heat.
If a code or maintenance message accompanies the sound, keep the exact display and continue with the Rinnai code guide linked above.
What each one takes
| Observation | Next job |
|---|---|
| Controller off or another controller has priority | Use the matching operation instructions with hot taps closed. |
| Heat starts only with a fuller hot draw | Compare flow with the model specification and investigate restrictions. |
| New installation has never heated | Installer review of connections, supplies and commissioning. |
| Filter, crossover or flow sensor investigation | Qualified water side and internal diagnosis. |
| RUR rapid In Use flash | Report pump operation without ignition, using that model’s indication chart. |
Questions people ask
Does the On/Off button isolate electrical power?
No. Rinnai explicitly separates the temperature controller from electrical isolation. Maintenance needs the supply disconnected by the method in the matching manual.
Can a Rinnai be too quiet to be working?
Sound alone is not the manual’s test. Use the controller state, water draw and operating indication together when describing the complaint.
Does a rapid RUR In Use flash mean it is heating?
The cited RUR manual identifies it as pump operation without ignition. Keep it separate from that manual’s solid and slow flashing indications.
Should I unplug the flow servo if the screen is blank?
Leave that RE diagnostic to a qualified technician. It involves internal components, and the chart describes a test for a specific symptom rather than routine resetting.
Is a beep always a fault?
The RU controller has normal keypress beeps and a setting to mute them. An ongoing sound needs its accompanying display identified before treating it as a button sound.
The other tankless guides: Rinnai error codes, tankless water heater problems and tankless error code guide.
Sources: Rinnai RU Installation and Operation Manual 100000467, RU199i family; RUR manual 100000508, RUR199i family; RE/VE Installation and Operation Manual linked from RE199iN, RE199i family; Value Series manual 100000258, V75i family: operation, no code diagnostics, maintenance and safety sections
By



