For a Goodman heat pump not heating, record whether the outdoor unit never starts, pauses during defrost or runs without warming the house. Goodman's GSZ14 installation reference and GSZC16/GSZC18 service manual describe different defrost controls. Match the model before using a timer or code chart.
If your Goodman heat pump is not heating, start by noting what it does. Is the whole system silent, does the outdoor fan pause, or does the equipment run while the room temperature keeps falling?
Goodman’s GSZ14 installation reference describes time and temperature defrost with SmartShift. Its GSZC16 and GSZC18 service manual has a separate communicating defrost sequence. Those differences matter when you are deciding whether a pause belongs to normal operation or needs investigation.
Before you start
What to carry: a torch, your thermostat instructions and the installation or service paperwork. Photograph the thermostat and an outdoor model label you can reach without opening a panel.
Which equipment? This guide uses the GSZ14 installation reference and the communicating defrost section in Goodman’s GSZC16/GSZC18 service manual. A package unit or another control needs its own instructions. The indoor unit and its backup heat also need identifying; do not assume a separate gas furnace is an electric heater.
Renting? Send maintenance the model, selected mode, displayed room and target temperatures, and the observations below. These are useful without reaching the control board.
The GSZ14 reference warns that multiple power sources may be present and requires all power disconnected before service. Goodman’s GSZC service manual reserves repairs for trained personnel. Capacitors, contactors, pressure switches, refrigerant and live voltage tests belong with service.
The GSZ14 instructions place defrost timer and SmartShift adjustments in system startup work. Do not move a board jumper or force a defrost test as an owner check.
Start with the symptom you can actually observe
Check the request before the outdoor unit
Read the selected mode and target temperature. If the screen is blank, says Off or shows an unexpected schedule, use that thermostat’s user instructions to correct the setting. Leave installer menus and wire connections alone.
Write down any message before changing a setting. If an installed GSZC control has already reported a fault at the thermostat or in a service record, use our Goodman heat pump code guide for its separately scoped PCBHR105 chart. You do not need to open the outdoor cabinet to look for a code.
For a running system, our general heat pump heating guide covers comparing room and supply air. Here, the next question is whether your Goodman is between heating and defrost, or has stopped altogether.
Look at the accessible air path and drainage
The GSZ14 reference lists a dirty air filter, dirty indoor coil and insufficient air across the indoor coil among its troubleshooting possibilities. Look at an accessible return filter and room openings. Follow the indoor unit’s user instructions if that filter needs attention; internal coil cleaning and blower adjustments are service work.
Outside, note snow, debris or ice around the unit and underneath it. The GSZ14 installation instructions require free drainage of defrost water and ice through the base area, with extra consideration for heavy snow and prolonged freezing weather.
Report ice filling the base or a unit buried in snow. Do not try to lift the cabinet or alter its support. Those observations give the installer a reason to inspect drainage and placement, rather than assuming every icing complaint needs a new defrost board.
Goodman’s defrost settings are not all the same
Match the defrost control before judging its timing
For the GSZ14 reference, Goodman describes a time and temperature control with selectable intervals of 30, 60 or 90 minutes. SmartShift delays compressor operation as defrost begins and ends. The manual provides a jumper setting for that feature, but changing it belongs to the installer.
In the communicating defrost section of RS6200007r25, Goodman gives 30, 60, 90 or 120 minute selections. The control accumulates compressor run time when the outdoor coil is cold enough, approximately 31 degrees F, and initiates defrost when that time is reached and heat is requested.
That is accumulated operating time under the stated conditions. It is not a promise of defrost at fixed intervals on a wall clock. In this communicating sequence, Goodman ends defrost at approximately 75 degrees F coil temperature or after a maximum of 10 minutes, whichever comes first.
Note whether ice clears and heating resumes. If it does neither, give service the model and how the cycle behaved. The winter icing guide explains the broader distinction between frost and an ice blockage.
If it stays stopped or keeps blowing cold
Keep fan, compressor and defrost complaints separate
The GSZ14 troubleshooting chart separates a system that will not start, a running fan with a compressor that will not start, an outdoor fan that will not start, and a system blowing cold air in heating. It also gives separate complaints for failure to start or end defrost.
Describe only what you can observe safely. A stationary fan and an audible sound from the cabinet do not require you to identify the compressor by touch. Note whether the event followed a thermostat replacement, power interruption or earlier repair, and include any error already visible.
Goodman’s chart lists a faulty reversing valve, defrost control and defrost thermostat among its possible causes. It calls for testing the defrost control and thermostat. A service diagnosis distinguishes those from electrical supply and airflow problems. The symptom alone does not select the part.
What each one takes
| Observation | Work involved |
|---|---|
| Unexpected thermostat mode or schedule | Normal user settings and the thermostat instructions |
| Accessible filter needs attention | The indoor unit’s specified filter care |
| Ice blocks the base or drainage | Installer review of drainage, support and snow exposure |
| Defrost does not restore heating | Matching the control, then testing its sensors and sequence |
| Fan or compressor does not run | Professional electrical and control diagnosis |
Questions people ask
Where is the GSZ14 installation manual?
The manufacturer-authored IOG-4002G installation reference is supplied with Alpine Home Air’s GSZ14 documents. Its startup section explains the defrost intervals and SmartShift.
Is the 120 minute setting in every Goodman?
No. Goodman’s communicating sequence includes that selection; the GSZ14 reference used here lists 30, 60 and 90 minutes. The installed control decides which instructions apply.
Does a pause during defrost mean the compressor failed?
The GSZ14 reference specifically describes SmartShift delays at defrost entry and exit. Report a system that fails to return to heating, rather than treating the pause alone as a failed compressor.
Can I press the board’s defrost test buttons?
Leave that to service. Goodman’s service manual assigns advancing the communicating heat pump into defrost to field service personnel.
Does this cover a Goodman gas furnace that will not light?
No. Use the Goodman furnace guide for a furnace message. Include both indoor and outdoor equipment details when requesting help with a combined system.
The other heat pump guides: outdoor unit not running, heat pumps in cold weather and heat pump resets.
Sources: Goodman GSZ14 Installation & Service Reference IOG-4002G, September 2022, published by Daikin Comfort Technologies Manufacturing, supplied through Alpine Home Air; Goodman Service and Troubleshooting RS6200007r25, April 2021, communicating defrost section page 21 and GSZC16/GSZC18 identification page 11, saved from InspectAPedia
By



