Free, independent repair guides
HeatCoolFix

Trane Heat Pump Not Heating: Settings and Changeover

Trane Heat Pump Not Heating: Settings and Changeover
Short answer

A Trane heat pump not heating after a switch from cooling needs a different report from one blowing air between heating calls. Trane advises checking Heat mode, fan Auto, filter condition and outdoor airflow. A failed changeover or a defrost cycle that does not restore heat needs service.

If your Trane heat pump cooled properly but will not heat after you change modes, tell the technician. Trane’s troubleshooting page points to a possible reversing valve problem in that situation. Air that feels cool only between heating calls has a different starting point: the thermostat’s fan setting.

Work through the checks below from the wall control and the outside of the equipment. Keep the timing of the fault in mind, because it tells the technician more than a guess at which part failed.

Before you start

What to carry: a torch, a phone and the thermostat’s user guide. Keep any recent installation or repair invoice nearby so you can report what changed.

Identify the system. Copy the outdoor model from an accessible label. The installation details below concern Trane’s 4TWR4 family in guide 18-BC95D1-4-EN. The 4TWV0 ComfortLink II system has a different service reference and its own Trane heat pump alert guide.

Gas or electric? Identify any indoor gas furnace separately from the electric outdoor heat pump. If the message is on that furnace, use the Trane furnace codes rather than an outdoor control chart.

Renting? Give maintenance the model, thermostat photo and whether this started when you changed modes. Leave cabinet access to their service person.

Do not turn an observation into a live test.
Trane’s 4TWR4 installer guide warns that exposed live electrical components can cause serious injury or death. Its 4TWV0 Service Facts requires qualified personnel and electrical isolation before service. Keep the service covers shut and your hands out of the fan grille.

Board test pins, compressor checks and refrigerant connections are professional work. The forced defrost procedure in an installer guide is not an extra thermostat setting for an owner to try.

Air moving is not the same as a call for heat

Check 1Normal thermostat controls; no parts or wiring work

Use Heat mode and check the fan setting

Trane’s first owner checks are Heat mode and fan Auto. Its explanation is useful: with the fan set to On, air can continue moving even when the heat pump is not actively heating.

Look at the screen rather than judging by the sound of air at a register. If it is still set to Cool, change it to Heat using the user guide. If the fan is On, try Auto as Trane recommends. Note the room temperature and target so you can tell whether the house is moving toward the setting.

THE FAN SETTING CHANGES WHAT YOU FEEL AFan OnAir can move between heating calls. BFan AutoTrane's recommended setting for this check.

Trane distinguishes a fan set to On, which can circulate air without active heating, from the Auto setting it recommends when checking this complaint. Airflow alone does not identify a heating failure.

If the screen itself is blank or will not accept changes, deal with that control problem first. Do not remove wires or change installer configuration to make a heating symbol appear.

Separate a defrost interruption from lost heating

Check 2Watching an accessible display and the next heating result

Watch for the return from defrost

Trane says a heat pump in defrost can blow cool air and should resume normal heating after that mode ends. If your thermostat displays defrost, note that message and whether the house starts warming again afterward.

Do not borrow a defrost duration from another Trane model. The 4TWR4 installer guide has separate defrost control sections for the 036D model and the other models. Their checkout instructions are not identical, so service must match the model and board.

A cycle that never returns to useful heating, or ice that remains a problem, is a reason to have the sequence checked. Our winter icing guide covers the broader frost and ice distinction.

Check 3Accessible filter care and clearing loose outside obstructions

Check the filter and outdoor breathing room

Trane links dirty filters and restricted outdoor airflow with poor heating, and says a dirty filter can contribute to overheating and shutdown. Inspect the normal user filter location and follow the indoor unit’s instructions for replacement.

At the outdoor unit, Trane advises clearing leaves, debris and snow from the top, and trimming nearby vegetation. Work from outside the grille; do not reach toward the fan or remove a guard.

For 4TWR4 installations in persistent freezing weather, Trane’s installer guide also calls for base pan drain holes to remain unobstructed. Snow drifts and refreezing meltwater are installation considerations. Photograph ice underneath the cabinet for service rather than trying to move or raise the unit yourself.

4TWR4: AIRFLOW AND MELTWATER BOTH MATTER ASnow at the sidesTell service where drifts build up. BDrainage below the coilReport ice blocking the base area.

Trane's 4TWR4 location guidance includes drainage through the base pan and avoiding snow buildup at the sides. Show an installer where ice remains; support and elevation changes are installation work.

If cooling worked but heating does not

Check 4Reversing valve and refrigeration diagnosis by a technician

Tell service when the changeover failed

Trane identifies a reversing valve that is stuck or has failed as a possible explanation when cooling worked recently but heating does not. That valve changes refrigerant direction between operating modes. Report the changeover history without treating it as proof that the valve needs replacing.

Include whether this began after a thermostat replacement or service visit. Let the technician investigate the control request as well as the equipment. Avoid switching back and forth between Heat and Cool to repeat the experiment.

Trane also lists low refrigerant as another possible heating problem. Its owner page advises prompt HVAC service for suspected leakage, including a hissing sound, pooled liquid or a frozen evaporator coil. Those signs need investigation; do not identify an unknown liquid as refrigerant or add a charge yourself.

What each one takes

Situation Work involved
Cool mode or continuous fan selected The normal thermostat controls
Dirty accessible filter or loose outdoor debris Specified filter care and an outside cleanup
Ice returns underneath a 4TWR4 Installer inspection of drainage and snow exposure
Defrost fails to restore heating Model-specific control and sensor testing
Heating fails after successful cooling Professional changeover and refrigerant diagnosis

Questions people ask

Should Trane vent air feel like furnace air?

Trane says heat pump air is warm rather than the hot air expected from a furnace. Use room temperature and the heating result alongside how the air feels.

Does this apply to every Trane defrost board?

No. Even the 4TWR4 installer guide separates the 036D control from the others. Another model needs its matching service instructions.

Where is the 4TWR4 installer guide?

Trane hosts 18-BC95D1-4-EN. It is a professional reference, including location guidance and electrical checkout procedures.

Should I reset a ComfortLink II alert first?

Record the complete message and use the matching alert guide linked above. That preserves the evidence for service before any equipment-specific reset is considered.

Does a hissing sound prove a refrigerant leak?

No. Trane lists hissing, pooled liquid and a frozen evaporator coil as possible signs of a leak.

The other heat pump guides: checking delivered heat, cold weather operation and an outdoor unit that stays off.

Sources: Trane Troubleshooting Tips for a Heat Pump Not Heating, trane.com; Trane 4TWR4 Installer's Guide 18-BC95D1-4-EN, August 2016, safety, location considerations and sections 11.3 on defrost controls; Trane Service Facts 4T-V0-SF-1A for 4TWV0 ComfortLink II equipment, safety pages 1 and 2